Publicidad
Idiomas disponibles
Idiomas disponibles
Assembly
Attaching and installing the lights
NOTE: Before assembly, carefully inspect all parts as listed
in the Package Contents table. If any part appears missing
or damaged, do not assemble this product, contact Hampton
Bay customer service.
□ Twist the bulb (E) into the lamp cap (A), clip the lamp cap (A) with cage
cap 2 (C), put the metal cage (D) in the cage cap 2 (C), then clip the metal
cage (D) with cage cap 1 (B), attach with screws. Figure 1.
□ Repeat step 1 until all the lamps are assembled. Figure 2.
A
E
Use and Care Instructions
CAUTION: To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch coverings of metal or
materials which look like metal, and b) Do not mount or support strings in a manner that can cut or damage wire insulation.
□ When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off
easily. Keep the tree holder filled with water.
□ If the product is placed on a tree, the tree should be well secured and stable.
□ Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or trayed wire insulation or cords, cracks in the lamp
holders or enclosures, loose connections, or exposed copper wire.
□ When storing the product, carefully remove the product from wherever it is placed, including tree, branches, or bushes, to avoid any undue strain or stress on
the product conductors, connections, and wires.
□ When not in use, store neatly in a cool, dry location protected from sunlight.
Warranty
For warranty information on this product, contact Hampton Bay Customer Service at 1-855-HD-HAMPTON or visit www.HAMPTONBAY.com.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC SDoC responsible party in USA: King of Fans Inc, 1951 N.W. 22nd Street Fort Lauderdale, FL 33311 USA 954-484-7500.
B
C
D
Figure 1
Figure 2
Replacing the fuse
WARNING: Risk of fire. Replace the fuse only with 5 Amp,
125 Volt fuse (provided with product).
WARNING: Risk of fire. Do not replace the attachment plug.
The plug contains a safety device (fuse) that should not
be removed. Discard product if the attachment plug is
damaged.
□ Grasp the plug and remove from the receptable or other outlet device.
Do not unplug by pulling on the cord.
□ Slide open the fuse cover on top of the attachment plug towards the
blades.
□ Remove the fuse (I) carefully.
□ Slide the fuse access cover close on top of the attachment plug.
□ Insert the connector closure (J) in female plug (G) when not in use.
Replacing the lamp
CAUTION: Replace bulbs with only the same type of 0.6 watt
max listed or Classified LED lamps.
CAUTION: Risk of fire. Do not deliberately reposition either
lamp holder contact.
Please contact 1-855-HD-HAMPTON for further assistance.
I
J
G
HAMPTONBAY.COM
Publicidad
