Palram Palermo 3600 Instrucciones De Montaje página 3

IMPORTANT
Please read
these instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order set out
in
these instructions.
Keep these
instructions
in
a
safe place
for future
reference.
»
Care
and Safety Advice
Please
follow the instructions
as
listed in
this manual.
Sort the parts and check against the contents list.
For
safety purposes we
strongly recommend the product to
be
assembled by at
least
two people.
Some parts have metal edges. Please be careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to assemble the Gazebo
in
windy
or
wet conditions.
Dispose of
all
plastic
bags safely
-
keep them away from children's
reach.
Keep children away from the assembly
area.
Do
not attempt to assemble the Gazebo if
you are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy spells.
When using
a
stepladder
or
power tools,
make sure
that
you are
following
the
manufacturer's safety advice.
Do
not climb or stand on the roof.
Heavy articles should not be leaned against the poles.
Keep
roof and gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on roof
can
damage the Gazebo making it unsafe to
stand
below
or nearby.
This
product
was
designed to
be used
mainly
as
a
Gazebo.
If color was scratched during assembly it
can be
fixed
with
the
following
tints:
Grey
-
RAL
7012
»
Cleaning instructions
In
order to
clean
the
Gazebo, use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
»
Tools
&
Equipment
T001
(Supplied)
el
Attention
Please
note you install the panels with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
and peel the film strip covering the panels.
Screws and plugs are not supplied.
Please
tighten
all screws
when completing
assembly.
Anchoring this product to the ground
is
essential to its
stability
and
rigidity.
It
is
required to complete this stage
in
order for your warranty to
be
valid.
During Assembly
During assembly use
a
soft surface below the parts to avoid scratches
and damages.
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
Step
6c:
Carefully spread silicone glue along the cross-section of the profile
and at once
attach the profiles together. Recommended to wipe the extra residue silicone.
Steps 7-12:
It
is
recommended to
use
a
carton or other soft material under the lowered
corner
in
order to avoid scratches and peeling of paint.
Step
11:
Optional
-
if you wish to add
Palram's
curtains/netting
-
Please
thread
16
of the
plastic clips
through the
rail in each
of the four profiles
in
order to hang the
curtains/netting (not supplied).
Steps 12+14:
Drawing
a
Please note
that threading of the
screws should be done from the outside
Steps 13+15:
Please
note
that threading of the
screws should
be
made
from the bottom
up.
Step 16b:
Please
add silicone on the inner
area
of
part
#
8327
as
illustrated
Step 23a:
Please
drill
holes in
the panels to
be
located precisely parallel to the holes
in
profiles #7744
+
#7743
Step 24:
Please level
the profiles'
legs and
adapt
screws and plugs
to your
specific
ground
type.