Westinghouse 77870 Instrucciones Para La Instalación

WARNINGS:
•
To avoid fire, shock, and serious personal injury, follow all
instructions carefully. Read and save these instructions for
future reference.
Do not install or use this unit if any part is damagedor missing.
•
• IMPORTANT! Fan installation must be complete, including the
assembly of blades, before testing the remote control unit.
NOTICE:
A. MAKING THE ELECTRICAL CONNECTIONS:
NOTE: This remote only works
with some fans when mounted
on sloped ceilings.
Do not use fan speed control in
canopies where the mounting
is not as described in figures
4 or 5. This remote cannot be
installed in a downrod style fan
when installed as flushmount
(when downrod is not in use).
1. Disconnect existing wring between ceiling fan and AC
supply at electrical junction box.
2. FOR FANS ON A DOWNROD: Remove ceiling fan canopy
from its mounting plate.
FOR FLUSHMOUNT FANS: Remove decorative housing
from mounting plate (see figure 2). Disconnect mounting
bracket from mounting plate and allow to hang from one
side (see figure 3).
3. Making the electrical connection (see Figure 1):
•
Connect GREEN fan wire to BARE (ground) wire.
•
Connect BLACK receiver unit wire to BLACK supply
wire (AC LINE).
•
Connect WHITE receiver unit wire to WHITE supply
wire (AC NEUTRAL).
•
Connect WHITE receiver unit wiree (MOTOR N) to
WHITE fan wire.
•
Push the connected wires up into the junction box.
Place BLACK wires on one side of box, and WHITE,
GREEN and BARE (ground) wires on the other side of
the box.
•
Connect BLACK receiver unit wire (MOTOR L) to BLACK
fan wire.
B. INSTRUCTIONS FOR YOUR NEW WESTINGHOUSE REMOTE FAN CONTROL SYSTEM
NOTE: Before installing this
unit, change the factory code
switch setting to your own
preferred setting.
Be sure the code switch
positions of the transmitter
and received match each
other or the ceiling fan will not
function.
If this unit causes interference
with other appliances, you
may need to select di erent
combinations.
C. SETTING THE OPERATING CONTROLS (FIRST TIME ONLY):
1. This unit operates on one 9 volt battery (included).
2. Store the controller unit away from excess heat or humidity.
3. This remote control unit is equipped with 16 code combinations.
Because of the many combinations, interference from other
remotes is possible (i.e. garage openers, car alarms, security
systems, etc.). If your fan/light goes on or o without using your
remote, change the code on both the control unit in the fan and in
your remote transmitter.
4. If your ceiling fan is equipped with variable speed and light ON/OFF
pull chain switch controls, make sure to set the speed control at
the HIGHEST speed and the light to the ON or BRIGHTEST position
before installing the remote control. This will avoid erratic speeds
TROUBLESHOOTING GUIDE
PROBLEM: REMOTE FAILS TO OPERATE
Check:
•
Is there power to the receiver unit?
•
Is the receiver unit wired correctly?
•
Are the fan and light switches set on the highest position?
•
Is there a good battery in the remote? If the red indicator lights when
either button is pushed, the battery is good.
PROBLEM: SHORT RANGE
Solution:
•
If the remote can operate the receiver unit when close to it but does
not operate it at distances of 30-50 feet, try placing the black
antenna wire above the ceiling and outside of the junction box.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com
and Westingouse are trademarks of Westinghouse Electric Corporation.
SAFETY PRECAUTIONS:
1. This remote control is rated for a maximum of 1.2 Motor amp at 120 Volts,
and total bulb wattage equaling 100 Watt maximum.
2. Do not use with DC solid state ceiling fans.
3. The decorative housing (canopy) at the ceiling must be metal. The metal
housing acts as a protective cover for the Control Unit. DO NOT USE WITH
A NON-METALLIC HOUSING.
4. Only the remote unit should be used to change fan speeds. Do not use the
pull chain to change fan speeds after installation.
5. Make sure no bare wires are exposed outside of the connectors.
FIGURE - 1
RECEIVER
UNIT
AC LINE BLACK BLACK
AC NEUTRAL WHITE WHITE
AC SUPPLY BARE (GROUND)
•
Connect BLUE receiver unit wire (FOR LIGHT) to BLUE light
wire.
•
Push the connected wires up into the junction box.
Lay the BLACK control unit wire (ANTENNA) on top of the
control unit.
•
FOR FANS ON A DOWNROD: Lay the control unit in the
canopy (see figure 4). Reinstall the canopy on this
mounting place. Restore electrical power to the circuit.
•
FOR FLUSHMOUNT FANS: Attach the control unit to the
mounting plate or to the ceiling with the supplied tie
wraps (see figure 5). Reconnect the mounting bracket to
the mounting plate (see figure 2). Reinstall the decorative
housing on its mounting plate. Restore electrical power
to the circuit.
NOTE: If the unit does not fit properly between the
mounting plate and ceiling, attach unit to the
underside of the mounting plate.
WARNINGS:HIGH VOLTAGE
Before connecting this control unit:
•
TRANSMITTER Disconnect electrical power from the circuit to be used.
(BACK OF REMOTE)
•
Household power can cause serious injury or death.
•
Wiring must meet all local electrical code requirements.
1. Setting the code on your new remote (see figure 6) .
•
Remove battery cover. Press firmly below arrow and slide battery cover o .
CODE SWITCHES
2. Slide code switches too your choice of UP and DOWN positions (use ball point
pen or small screwdriver to slide firmly up or down). Factory setting is all UP.
Do NOT use this setting.
3.
Setting the code on your new control unit (see figure 7).
•
FIGURE - 6
Slide code switches to the same positions as set on your REMOTE.
NOTE: The codes switches on the transmitter and the receiver unit must be
set to the same positions to work.
and possible damage to your ceiling fan.
5. Operation buttons on the panel of the transmitter:
1 - Fan High speed
2 - Fan Medium speed
3 - Fan Low speed
0 - Fan O
Light Bulb - LIGHT brightness and ON/OFF control
6. To turn ON the fan, press the selected speed button to run the fan
at the desired speed.
7. To turn OFF the fan, press the "0" button
8. For LIGHT control: Turn the LIGHT ON?OFF by pressing the light bulb
button. If you keep the light bulb button pressed, the LIGHT will dim,
LIMITED WARRANTY
The Westinghouse remote control for ceiling fans o ers a limited
warranty of one year from the date of purchase to the original owner
against defects in material and workmanship. All spare parts are
covered for ninety days only. This warranty is in lieu of all other
warranties expresses or implied.
Westinghouse will repair or replace this remote control if it is
defective due to faulty materials or workmanship. This warrantydoes
not cover service charges, batteries, defects resulting from accidents,
damages caused through abuse or alterations or by a xing any
attachment not provided with the product, improper installation or
maintenance, failure of supporting devices not supplied as original
mounting hardware, exposures to extemes of heat or humidity,
incorrect
Used under license by Westinghouse Lighting.
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
FLUSHMOUNT FANS ONLY
BLUE BLUE LIGHT
FAN
BLACK BLACK
WHITE WHITE FAN
GREEN
FAN
FIGURE - 4
DOWNROD FANS ONLY
RECEIVER
UNIT
All Rights Reserved. Made in China
Installation & Operating Instructions for the
Westinghouse Ceiling Fan and Light Remote Control
6. All wiring must conform to national and local electrical codes. If youfeel
that you do not have enough electrical wiring knowledge or experience,
have your fan control installed by a qualified licensed electrician. Any
described in this manual should be performed by a qualified licensed
electrician.
7. Do not use water or detergents to clean the remote transmitter unit. A
dry dust cloth will be suitable for most cleaning.
8. Use of this control with some ceiling fans could result in fire, shock, and
serious personal injury. Use this fan control only with capacitor speed
controlled ceiling fans only.
FIGURE - 2
FLUSHMOUNT FANS ONLY
FIGURE - 5
FLUSHMOUNT FANS ONLY
CEILING JUNCTION BOX
FIGURE - 7
WIRES
go o , and come back on at the brightest lvel. The LIGHT wil continue
to cycle until the light bulb button i s released. If you turn your power
source o , the settings on your fan and lighting will not remain the
same when you turn the power back on.
incorrect voltage, surges in current,unauthorized repair, or failures
caused by modifications of the product ot the acts of third parties.
See remote manual for proper installation.
If this product fails for any reason covered by this warranty,
please contact us at www.westinghouselighting.com/contact-us.
77870
FIGURE - 3
RECEIVER UNIT
MOUNTING PLATE
WIRES
CODE SWITCHES
RECEIVER
(CONTROLLER UNIT)
WIRES