Retekess TA007 Guia Del Usuario página 6

Standby Mode
If the signal volume of the audio input is too low, the SIGNAL indicator light will be on for 1MIN, then the
white light will flash slowly (0.5s on/0.5s off), If there is no audio input for more than 4min, the white light
turns off and enters standby mode (When there is audio input again, the SIGNAL indicator will reactivate
and enter the state of steady white light.）
Headphones
Power on/off
Long press the "power button" of the headphones for 2 seconds to turn on the power indicator light will
always be red, and "Power on" will be broadcast.
Long press the "power button" of the headphones for 2 seconds to turn off, the power indicator light will off,
and "Power off" will be broadcast.
2.4G/Bluetooth BT Mode Selection (Default 2.4G When Booting)
After the headphones are turned on, short press the "mode selection" button. The SIGNAL indicator light of
the headphones will be white in TV 2.4G mode; SIGNAL indicator light will be blue in BT connection mode.
Connection Mode Priority
Every time the headphones is turned on, it is in TV Headphones mode. If the headphones has a pairing
record with the mobile phone before, the headphones will be connected to the mobile phone again, but the
Bluetooth Headphones mode does not work, and the headphones needs to be switched to Bluetooth mode
to start working.
Pairing
In 2.4G mode, press and hold the headphones "2.4G/Bluetooth switch button" for 5s to enter the pairing
state. At this time, the SIGNAL signal light of the headphones enter the state of white light flashing quickly
(0.25s on/0.25s off); at this time, connect the power adapter cable of the transmitter to the power supply. If
the pairing is successful, the SIGNAL indicator of the transmitter will always be white, and the SIGNAL
indicator of the headphones will also be always white (the headphones will broadcast TV Connected). If the
pairing fails, the SIGNAL will not stay on white.
Short press the "2.4G/Bluetooth mode switching button" to put the headphones into Bluetooth mode --
SIGNAL enters the blue light flashing slowly (0.5s on/0.5s off), and the headphones broadcasts "Bluetooth
Headphones". At this time, under the Bluetooth function of the mobile phone, search for the list of
connectable devices - select "RETEKESS TA007" to complete the Bluetooth pairing (Bluetooth connected
will be broadcast and the SIGNAL light will be steady blue if the pairing is successful).
Failed to Connect Normally After Booting
In 2.4G mode, if the headphones are not connected back to the previous transmitter normally after turned
on, the SIGNAL indicator will turn white and flash slowly (0.5s on/0.5s off), enter the reconnection state, and
automatically shut down after no operation within 5min ( Announces Power off when shutting down).
In Bluetooth mode, after turning on the headphones and switching it to Bluetooth mode , if the headphones
cannot be connected back to the Bluetooth device that was paired successfully in the past (disconnection
occurs), the SIGNAL indicator light will flash blue slowly (0.5s on/0.5s off),the headphones enter the
alternate state of reconnection and pairing, and automatically shut down after no operation within 5min
(playing Power Off)
Disconnect
In 2.4G mode, turning off the power of the transmitter in the connected state, and the SIGNAL indicator of
the headphones enter the reconnection state, the white light flashes slowly at this time (0.5s on/0.5s off),
and they will automatically shut down after 5min without operation.( Announces Power off when shutting
down).
In Bluetooth mode, turning off the Bluetooth function of the mobile phone, and then disconnect the
Bluetooth connection with the headphones. At this time, the headphones SIGNAL will flash blue light slowly
(0.5s on/0.5s off) to enter the alternate state of reconnection and pairing, and they will automatically shut
down after 5 minutes of no operation. ( Announces Power off when shutting down).
Pairing Distance Exceeded
04