Bosch 060186810H Manual Original página 13

(10) Handle (insulated gripping surface)
a)
(11) Universal bit holder
a)
(12) Screwdriver bit
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Drill/Driver
Article number
Rated voltage
A)
No-load speed
– First gear
– Second gear
Max. torque, hard/soft
screwdriving application ac-
A)
cording to ISO 5393
Max. drilling diameter
– Steel
– Wood
Max. screw diameter
Chuck capacity
Weight according to EPTA-
B)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation and dur-
ing storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery GBA 12V
1.3Ah.
B) Measured with GBA 12V 2.0Ah and GBA 12V 6.0Ah.
Noise/vibration information
Noise emission values determined according
to EN 62841-2-1.
Typically, the A-weighted sound pressure level of the power
tool is 72 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling in metal: a <2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
Bosch Power Tools
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
GSR 12V-15
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
3 601 H68 1..
not actually being used should also be taken into account.
V= 12
This may significantly reduce vibration and noise emissions
over the total working period.
-1
Implement additional safety measures to protect the oper-
min 0–400
ator from the effects of vibration, such as servicing the
-1
min 0–1300
power tool and application tools, keeping their hands warm,
Nm 30/15
and organising workflows correctly.
Assembly
u
mm 10
mm 19
mm 7
mm 1.0–10
kg 1.0–1.2
Charging the Battery (see figure A)
u
°C 0 to +35
°C –20 to +50
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
GBA 12V...
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
GAL 12... does not damage the battery.
GAX 18...
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (5), press the release buttons (4) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Follow the instructions on correct disposal.
Changing the Tool (see figure B)
u
2
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
1 609 92A 6NE | (12.08.2021)
English | 13