Publicidad
Idiomas disponibles
Idiomas disponibles
EN
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
HALF LOAD - If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and detergent.
Remember to halve the amount of detergent.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
-
PUSH&GO
Push&Go button is an easily distinguishable button that
allows you direct access to the Push&Go program, a wash and dry cycle
that ensures great cleaning performance in a short time. You don't have to
worry which program to choose, Push&Go cycle will do the work for you.
LOADING THE RACKS
UPPER RACK
(loading example for the upper rack)
Load delicate and light dishes: glasses,
cups, saucers, low salad bowls.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.)
please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
TROUBLESHOOTING
PROBLEMS
POSSIBLE CAUSES
The dishwasher does
No water in the water supply or the tap is closed.
not fill the
water. Display shows:
The inlet hose is bent.
and F6, both On/Off
and START/Pause LEDs
The sieve in the water inlet hose is clogged; it is
are blinking rapidly.
necessary to clean it.
Dishwasher finishes
Drain hose positioned too low or siphoning into
the cycle prematurely.
home sewage system.
Display shows: F15 and
both On/Off and START/
Pause LEDs are blinking
Air in water supply.
rapidly.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
2
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
(loading example for the
B
A
C
Please scan the QR code on your product in order to have more detailed information.
-
DELAY
The start of the program may be delayed for a period of time
between 0:30 and 24 hours
The DELAY function cannot be set once a wash cycle has been started.
WATER TAP CLOSED – Alarm
Flashes when there is no inlet water or water tap is closed.
DRAIN OUT - To stop and cancel the active cycle, the Drain Out
function can be used. A long press of START/PAUSE button, will
activate the DRAIN OUT function. The active program will be stopped and
the water in the dishwasher will be drained out.
LOWER RACK
For pots, lids, plates, sa-
lad bowls, cutlery etc.
Large plates and lids
should ideally be pla-
ced at the sides to avo-
id interferences with
the spray arm.
The lower rack has tip-
-up supports which
can be used in a verti-
cal position when ar-
ranging plates or in a
horizontal position (lo-
wer) to load pans and
lower rack)
salad bowls easily.
More information in the Daily Reference Guide on website.
CLEANING THE SPRAY ARMS
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
Please scan the QR code on your product in order to have more detailed information.
SOLUTIONS
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
After having carried out the verification and cleaning, turn off and turn on the dishwa-
sher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
Quick Guide
CAPACITY: 14 standard place-settings
CUTLERY BASKET
The
equipped with top
grilles for impro-
ved cutlery arran-
gement. The cutle-
ry basket should
be positioned only
at the front of the
lower rack.
Knives and other utensils with sharp
edges must be placed in the cutlery
basket with the points facing down-
wards or they must be positioned
horizontally in the tip-up compart-
ments on the upper rack.
The lower spray arm may
be removed by pulling it
upwards.
:
basket
is
IEC 436
Publicidad
