Festool TS 75 EBQ Manual De Instrucciones página 16

English
Wear a P2 respiratory mask to pro­
tect your health.
– Always connect the machine to a dust ex­
tractor when performing work that gener­
ates dust.
Only for AS/NZS: The tool shall always be
–
supplied via residual current device with a
rated residual current of 30 mA or less.
Cutting procedures
DANGER: Keep hands away from
–
cutting area and the blade. Keep your sec­
ond hand on auxiliary handle, or motor
housing. If both hands are holding the saw,
they cannot be cut by the blade.
– Do not reach underneath the workpiece.
The guard cannot protect you from the
blade below the workpiece.
Adjust the cutting depth to the thickness of
–
the workpiece. Less than a full tooth of the
blade teeth should be visible below the
workpiece.
– Never hold the workpiece in your hands or
across your leg while cutting. Secure the
workpiece to a stable platform. It is impor­
tant to support the work properly to mini­
mise body exposure, blade binding, or loss
of control.
– Hold the power tool by insulated gripping
surfaces, when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a "live"
wire will also make exposed metal parts of
the power tool "live" and could give the op­
erator an electric shock.
– When ripping, always use a rip fence or
straight edge guide. This improves the ac­
curacy of cut and reduces the chance of
blade binding.
Always use blades with correct size and
–
shape (diamond versus round) of arbour
holes. Blades that do not match the mount­
ing hardware of the saw will run off-centre,
causing loss of control.
Never use damaged or incorrect blade
–
washers or bolt. The blade washers and
bolt were specially designed for your saw,
for optimum performance and safety of op­
eration.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched,
jammed or misaligned saw blade, causing
16
an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or jammed tight­
ly by the kerf closing down, the blade stalls
and the motor reaction drives the unit rap­
idly back toward the operator;
– if the blade becomes twisted or misaligned
in the cut, the teeth at the back edge of the
blade can dig into the top surface of the
wood causing the blade to climb out of the
kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or in­
correct operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
– Maintain a firm grip with both hands on
the saw and position your arms to resist
kickback forces. Position your body to ei­
ther side of the blade, but not in line with
the blade. Kickback could cause the saw to
jump backwards, but kickback forces can
be controlled by the operator, if proper pre­
cautions are taken.
When blade is binding, or when interrupt­
–
ing a cut for any reason, release the trig­
ger and hold the saw motionless in the
material until the blade comes to a com­
plete stop. Never attempt to remove the
saw from the work or pull the saw back­
ward while the blade is in motion or kick­
back may occur. Investigate and take cor­
rective actions to eliminate the cause of
blade binding.
When restarting a saw in the workpiece,
–
centre the saw blade in the kerf so that
the saw teeth are not engaged into the
material. If a saw blade binds, it may walk
up or kickback from the workpiece as the
saw is restarted.
Support large panels to minimise the risk
–
of blade pinching and kickback. Large pan­
els tend to sag under their own weight.
Supports must be placed under the panel
on both sides, near the line of cut and near
the edge of the panel.
– Do not use dull or damaged blades. Un­
sharpened or improperly set blades pro­
duce narrow kerf causing excessive fric­
tion, blade binding and kickback.
Blade depth and bevel adjusting locking
–
levers must be tight and secure before
making the cut. If blade adjustment shifts
while cutting, it may cause binding and
kickback.