DeWalt XR DCS367 Traducido De Las Instrucciones Originales página 34

EngLIsh
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
nOTE: Make sure your battery pack is fully charged.
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack with the rails inside the tool's
6
handle (Fig. C).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Variable Speed Trigger Switch (Fig. D)
Lock-off Button and Trigger switch
Your saw is equipped with a lock-off button
To lock the trigger switch, press the lock-off button as shown
in Figure D. Always lock the trigger switch
storing the tool to eliminate unintentional starting. The lock-
off button is colored red to indicate when the switch is in its
unlocked position.
To unlock the trigger switch, press the lock-off button as
shown in Figure D. Pull the trigger switch to turn the motor ON.
Releasing the trigger switch turns the motor OFF.

WARNING: This tool has no provision to lock the switch
in the ON position, and should never be locked ON by any
other means.
32
WALT battery packs and chargers.
and firmly pull the
7
2 .
1 when carrying or
The variable speed trigger switch will give you added versatility.
The further the trigger is depressed the higher the speed of
the saw.

CAUTION: Use of very slow speed is recommended only
for beginning a cut. Prolonged use at very slow speed may
damage your saw.
Worklight (Fig. A)
There is a worklight located on the end of the tool near the
9
shoe. The worklight is activated when the trigger switch is
depressed. When the trigger is released, the worklight will stay
illuminated for up to 20 seconds.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Blade Installation and Removal
(Fig. A, E, F, I)
Different blade lengths are available. Use the appropriate blade
for the application. The blade should be longer than 90 mm and
should extend past the shoe and the thickness of the workpiece
during the cut. Do not use jigsaw blades with this tool.

WARNING: Cut hazard. Blade breakage may occur if the
blade does not extend past the shoe and the workpiece
during the cut (Fig. E). Increased risk of personal injury, as
well as damage to the shoe and workpiece may result.
To install blade into saw
1. Pull blade clamp release lever
2. Insert blade shank from the front.
3. Push blade clamp release lever down.
nOTE: The blade can be installed in four positions as shown
in figure F. The blade can be installed upside-down for flush
cutting. Refer to figure J.
To Remove blade from saw

CAUTION: Burn hazard. Do not touch the blade
immediately after use. Contact with the blade may result
in personal injury.
1. Open up blade clamp release lever.
2. Remove blade.
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
3 up (Fig. A).