Cleaning The Exhaust Filter; Spare Parts And Accessories; Before You Send In The Appliance - Dirt Devil C-POWER XS Manual De Instrucciones

5 Maintenance

5.3 Cleaning the exhaust filter

12
13

5.4 Spare parts and accessories

ATTENTION:
Only use original spare parts from the scope of delivery or those which
you have purchased by reordering.
Accessory parts and spare parts can be reordered:
Contact Page 62, „International Service"

5.5 Before you send in the appliance

WARNING:
Risk of injury! Never use a faulty appliance! Always switch off the appli-
ance and disconnect it from the mains before starting troubleshooting
chapter 4.3, „Switching off".
Before contacting or even sending the appliance to us, use the following ta-
ble to check whether you can correct the problem yourself.
Problem
Cleaning indi- The dust bin is full.
cator (Fig. 1/
Empty the dust bin,
6) lights up or
module".
cleaning re-
sults are not The filters are dirty.
satisfactory.
Clean the respective filter
bin and motor protection filter" or
ing the exhaust filter".
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long wood-
en stick (e.g. a broomstick) to do this.
A
A
Solution
chapter 5.1, „Emptying the dust bin
chapter 5.2, „Cleaning dust
chapter 5.3, „Clean-
B
Check the exhaust filter every time you clean the motor protection filter
chapter 5.2, „Cleaning dust bin and motor protection filter" and clean it if
it is dirty.
1. Switch off the appliance,
2. Push the release catch of the exhaust filter cover down (Fig. 12/A) and
open the exhaust filter cover.
3. Remove the exhaust filter (Fig. 12/B).
4. Hold the dust bin over a dustbin.
5. Remove any residual dust by tapping. If the exhaust filter is still dirty,
thoroughly rinse it by hand until all dirt is removed.
ATTENTION:
The filter is washable, but it may not be cleaned in dishwashers or wash-
ing machines. Also, do not use detergents or brushes with hard bristles
B
to clean them. Let the filter dry for approx. 24 hours at room temperature
after washing it. Only put it back in place when it is completely dry.
6. If the exhaust filter is damaged, replace it ( chapter 5.4, „Spare parts
and accessories").
7. Put the exhaust filter holder with the freshly fitted filter back into its
bracket (Fig. 13/A).
8. Attach the exhaust filter cover at the bottom side first (Fig. 13/B) before
folding it up firmly. It will audibly snap into place.
The following accessories and spare parts can be reordered:
Item number
2815001
Motor protection filter set consisting of: 1 foam plastic
filter element (round) + 1 filter holder = 1 dual motor
protection filter; 1 small motor protection filter
2815002
1 exhaust filter
M203
1 parquet brush
M209
1 turbo brush
M219
1 mini turbo brush
Problem
The vacuum Overheating protection has tripped (possibly because
cleaner stops you ignored the lit cleaning indicator for too long).
suddenly. Switch the appliance off and pull the plug out of the sock-
et. Eliminate the cause of overheating (e.g.
5.2, „Cleaning dust bin and motor protection filter"). Wait
for about 45 minutes. After the appliance has cooled off,
you may switch it on again.
The cleaning The bypass vent (Fig. 1/20) is open.
results are un-
Close the bypass vent (Fig. 1/20).
satisfactory in
spite of the The attached nozzle is unsuitable.
appliance
Change the nozzle,
working cor-
nozzle".
rectly (clean-
ing indicator The position of the "carpet/hard floor" selector (Fig. 1/27)
(Fig. 1/6) is inappropriate.
does not light
Set the "carpet/hard floor" selector (Fig. 1/27) to the cor-
up).
rect position for the type of floor,
vacuum", step 4.
NOTE:
If you were unable to solve the problem using the information in the table
above, please contact our Customer Service (contact
„International Service").
chapter 4.3, „Switching off".
Content
Solution
chapter
chapter 3.2, „Selecting the proper
chapter 4.2, „How to
Page 62,
19