Publicidad
Node 605 computer case
Node 605 is the first in a new series of computer cases from Fractal Design specifically
designed to be used as centerpieces in modern and stylish home digital entertainment
environments.
With Scandinavian style and functionality in focus, Node 605 interface connectors, card
reader and optical disk drive have been hidden behind a door on the black-anodized alu-
minum front panel; whereas inside, thick sound-absorbing material and hard drive brackets
with silicone mounting bushings dampen vibrations. These features make Node 605 nearly
unseen and unheard during use.
Installation / instructions
To take full advantage of the features and benefits of a Node 605 computer case, the follow-
ing information and instructions are provided.
Unpacking and preparing
1. Remove the computer case from its protective packaging.
2. Undo the two screws on the rear and remove the cover.
3. Unscrew and remove the hard drive cages.
4. If an optical disk drive will be installed, unscrew and remove the cover plate from
the front panel.
Installing an additional fan – optional
Node 605 is supplied with two 120mm Silent Series R2 hydraulic bearing fans in
the front part of the case, mounted to draw air inside. When using components that
produce excessive heat, a third 120mm fan in the rear right position is recommended.
Typically, the best results are achieved by mounting this fan so that the airflow is
directed out of the case.
Installing the motherboard
1. Prepare the motherboard by installing the processor, CPU cooling and system
memory.
2. Fasten the standoff screws used for the current motherboard format.
3. Install the I/O plate – normally included with the motherboard.
4. Insert the motherboard – the center support strut can be removed to make installa-
tion easier.
5. Secure using the provided screws.
6. Connect front panel cables to the motherboard.
Installing an optional, slim optical disk drive (ODD)
1. Attach the mounting supports to the ODD – use the taller supports on the flat side.
2. Set the computer case on its side and insert the ODD.
3. Secure the ODD from the bottom of the computer case.
Installing the power supply
1. Insert the power supply.
2. Secure with provided screws.
3. Connect the power cables to the motherboard and installed devices.
3
Fr ac ta l D es ig n
For optimal performance, Fractal Design recommends using a power supply with a
120–140mm fan, positioned to face the computer case side; installation in the reverse
direction is also supported, in the event the Node 605 is placed closely to a wall.
Installing expansion cards
1. Remove the screw securing the expansion slots cover.
2. Unscrew the cover plates for the expansion slots to be used.
3. Install the expansion card onto the motherboard and secure to case with screw.
4. Reinstall the expansion slots cover and tighten the screw.
5. Connect any associated expansion card power cables.
Securing cables – recommended
For maximum air flow and easier installation of the hard drive cages, it is recom-
mended that power, front panel button, LED, and interface connection cables are all
bundled and fastened to the bottom of Node 605 using the supplied cable ties.
Installing hard disk drives/solid state drives (HDDs/SSDs)
1. Secure storage drives to the inner cage:
a) 3.5" HDDs should be secured using screws inserted through the silicone grom-
mets. Do not secure too tightly; this reduces the damping effect of the bushings.
b) 2.5" HDDs/SSDs should be secured using the countersunk screw holes.
2. Connect all cables to the devices, taking care to bend the cables in such a way that
the cage can easily be inserted into the computer case.
3. Insert the cage and screw it to the side panel and center support bar.
4. If more than two storage devices locations are needed, repeat these steps using
the outer cage.
Functionality and usability
Air filters
Filters are installed at the four air intakes on the sides of the Node 605 to prevent dust
from entering the case. To ensure optimal cooling, filters should be cleaned at regular
intervals. The filters are easily cleaned with a damp cloth, but can also be removed
and rinsed with water to remove fastened dirt.
Card Reader
Under the front door panel, Node 605 features a card reader for the following memory
cards formats: SD, MicroSD, and Compact Flash. The card reader should be con-
nected to an internal USB or USB2 connector on the motherboard, which will makes it
detectable by most operating system software.
Fan Control
Near the front, on the right side panel, of Node 605 is a fan controller. The fan control-
ler has three positions:
•
Top position - full speed (12V)
•
Middle position – off
•
Bottom position – low speed (5V)
The included fans can also, if desired, be connected to the motherboard for automatic
control (see motherboard manual for instructions).
No de 605
4
Publicidad
