Storage; Maintenance; Replacement Parts - Desa 28BN Manual Del Propietário

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION
Continued
9. Push knob in and quickly press IGNITOR button (see Figure 14).
Repeat until heater is lit. This can be easily done by placing
index finger in access hole on left of control cover and push-
ing ignitor with thumb (see Figure 14).
10. Continue holding knob in for approximately 30 seconds. Heater
should remain lit in the LOW heat setting.
11. For more heat, press knob and rotate counterclockwise to
HIGH setting.
12. If RELIGHTING, wait 5 minutes for heater to cool and gas to
clear, then follow steps 4 through 11.
Access
Hole in
Control Box
Figure 14 - Piezo and Control Knob Locations
SHUTDOWN INSTRUCTIONS
1. Press control knob and rotate clockwise to OFF position.
2. Close propane/LP cylinder valve (rotate knob clockwise).

STORAGE

CAUTION: Disconnect heater from propane/LP
supply cylinder.
1. Do not store heater while attached to propane/LP cylinder. Close
cylinder valve. Remove the hose/regulator assembly from the
propane/LP cylinder by turning the fuel gas connector nut
clockwise.
2. Store propane/LP cylinder in safe manner. Refer to Chapter 5
of Standard for Storage and Handling of Liquefied Petroleum
Gases, ANSI/NFPA 58. Follow all local codes. Always store
propane/LP cylinders outdoors. Never store propane/LP cyl-
inder in an enclosed area.
3. Store in a dry, clean, and safe place.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
107396-01F
Control Knob
Piezo
Ignitor

MAINTENANCE

WARNING: Never attempt to service heater while
it is connected to propane/LP supply, operating, or
hot. Severe burns can occur. Any guard or other
protective device removed for servicing must be
replaced prior to operating the heater.
1. Keep heater clean. Remove any debris from ventilation open-
ings (see Figures 12 and 13, page 6).
2. Inspect heater before each use. Check connections for leaks. Ap-
ply mixture of liquid soap and water to connections. Bubbles form-
ing show a leak that must be corrected. Correct all leaks at once.
3. Inspect hose/regulator assembly before each use. If hose is highly
worn or cut, replace it immediately. At least annually, remove hose/
regulator assembly from heater to inspect entire length of hose.
4. Spiders and insects can create a dangerous condition that may
damage heater or make it unsafe. Keep burner area clean of all
spiders, webs, or insects.
5. Have heater inspected yearly by a qualified service person.

REPLACEMENT PARTS

WARNING: Use only original replacement parts. This
heater must use design-specific parts. Do not substitute
or use generic parts. Improper replacement parts could
cause serious or fatal injuries. This will also protect your
warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can't supply
original replacement part(s), either contact your nearest Parts Cen-
tral or call DESA Heating Products' Technical Service Department
at 1-866-672-6040.
When calling DESA Heating Products, have ready
• your name
• your address
• model and serial numbers of your heater
• purchase date
• how heater was malfunctioning
In most cases, we will ask you to return the part to the factory.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can't supply original
replacement part(s), either contact your nearest Parts Central listed in
the Authorized Service Center booklet supplied with heater or call
DESA Heating Products at 1-866-672-6040 for referral information.
When calling DESA Heating Products, have ready
• model number of your heater
• the replacement part number
OPERATION
STORAGE
MAINTENANCE
REPLACEMENT PARTS
7 7

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido