Audio Settings - Kenwood KMM-DAB403 Manual De Instrucciones

AUDIO SETTINGS

While listening to any source...
1
Press the volume knob to enter [FUNCTION].
2
Turn the volume knob to select an item (see the following table),
then press the knob.
3 2
Repeat step until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press
AUDIO CONTROL
SUB-W LEVEL –15 to +15 (0) Adjusts the subwoofer output level.
BASS LEVEL –8 to +8 (+2)
Adjusts the level to memorize for each source. (Before
MID LEVEL –8 to +8 (+1) making an adjustment, select the source you want
to adjust.)
TRE LEVEL –8 to +8 (+1)
EQ PRO (This setting is stored to [USER].)
BASS ADJUST BASS CTR FRQ 60/80/100/200: Selects the center frequency.
BASS LEVEL –8 to +8 (+2): Adjusts the level.
BASS Q FACTOR 1.00/1.25/1.50/2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels.
MID ADJUST MID CTR FRQ 0.5KHZ/1.0KHZ/1.5KHZ/2.5KHZ: Selects the center
frequency.
MID LEVEL –8 to +8 (+1): Adjusts the level.
MID Q FACTOR 0.75/1.00/1.25: Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ 10.0KHZ/12.5KHZ/15.0KHZ/17.5KHZ: Selects the
center frequency.
TRE LEVEL –8 to +8 (+1): Adjusts the level.
12 ENGLISH
PRESET EQ
BASS BOOST
.
LOUDNESS
Default: XX
SUBWOOFER SET
LPF SUBWOOFER
SUB-W PHASE
FADER
BALANCE
VOLUME OFFSET
SOUND RECNSTR
(Sound reconstruction)
• [SUB-W LEVEL]/[SUBWOOFER SET]/[LPF SUBWOOFER]/[SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
DRIVE EQ/TOP40/POWERFUL/ROCK/POPS/EASY/JAZZ/NATURAL/
USER: Selects a preset equalizer suitable to the music genre.
(Select [USER] to use the settings made in [EQ PRO].)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or
running noise of the tyres.
LV1/LV2/LV3: Selects your preferred bass boost level. ; OFF: Cancels.
LV1/LV2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
ON: Turns on the subwoofer output. ; OFF: Cancels.
THROUGH: All signals are sent to the subwoofer. ;
85HZ/120HZ/160HZ: Audio signals with frequencies lower than
85 Hz/120 Hz/160 Hz are sent to the subwoofer.
REVERSE (180°)/NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum
performance. (Selectable only if a setting other than [THROUGH] is
selected for [LPF SUBWOOFER].)
R15 to F15 (0): Adjusts the rear and front speaker output balance.
L15 to R15 (0): Adjusts the left and right speaker output balance.
For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Preset the initial
volume level of each source. (Before adjustment, select the source you
want to adjust.)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression. ; OFF: Cancels.