OBJ_BUCH-2307-002.book Page 7 Tuesday, March 3, 2015 9:09 AM
English
Read and strictly observe the safety warnings in the oper-
ating instructions of the cordless drill/driver.
Hammer Safety Warnings
Wear ear protectors. Exposure to noise can cause hear-
ing loss.
Use the auxiliary handle provided with the GHA FC2
hammer adapter. Loss of control can cause personal in-
jury.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Additional Safety and Working
Instructions
Wear protective gloves. The hammer adapter may be-
come hot when operated for extended periods of time.
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Inserting SDS-plus Drilling Tools: Check the latching by
pulling the tool.
Replace a damaged dust protection cap immediately.
The dust protection cap largely prevents the penetration of
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap
is not damaged.
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Bosch Power Tools
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
To save energy, only switch the power tool on when using
it.
If the application tool should become blocked, switch
the machine off. Loosen the application tool.
When switching on with a blocked drilling tool, high
torque reaction can occur.
To make it easier to dismount the hammer adapter
from the power tool, run the application tool 2 to 3
turns in left rotation (see figure 9, page 132).
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Avoid unintentional switching on. Ensure the On/Off
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the machine in a better and safer
manner.
Symbol
Meaning
GSR 14,4 V-EC FC2/
GSR 18 V-EC FC2:
Cordless Drill Driver
Grey-marked area: Handle
(insulated gripping surface)
GHA FC2:
Hammer adapter
Grey-marked area: Handle
(insulated gripping surface)
Article number
Read all safety warnings and all instruc-
tions
Before any work on the machine itself,
remove the battery from the power tool.
Wear protective gloves
English | 7
1 609 92A 0YJ | (3.3.15)