Remote Control; How To Install Batteries; Battery Precautions - Insignia IS-TV040925 Manual Del Usuario

REMOTE CONTROL

1
POWER
1 2
2
4
7
3
0 QUICK VIEW
4
SLEEP
5
VOL
6
MENU
–
7
RESET
TV/AV
8
9
1. POWER Button - Press to turn the TV on. Press again to
turn the TV off.
2. Direct Channel Selection Buttons (0-9) - Allows direct
access to any channel.
3. QUICK VIEW Button - This button allows you to go back
to the previous channel selected by just pressing the
QUICK VIEW button. Press this button again to return to
the channel you were watching.
Before using the remote control, batteries must first be installed.

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.
2. Install two "AAA" batteries (not supplied).
3. Replace the battery compartment cover.
3T30631A [E] P02-07
3
5 6
10
8 9
CALL
11
MUTE
CH
12
VOL
13
ENTER
CH
+
SET
14
AUDIO
SELECT
CH.1/2
TV 15
CAP/TEXT
16
5
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button. The clock will
count down 10 minutes each time the button is pressed in
the order of 120, 110, 100, ······ 20, 10, 0. After the sleep
time is programmed, the display will disappear then
reappear momentarily every ten minutes to remind you the
sleep timer function is operating. To confirm the sleep time
setting, press the SLEEP button once and the remaining
time will be momentarily displayed. To cancel sleep time,
press the SLEEP button repeatedly until the display turns
to 0.
5. VOL (VOLUME) / Buttons - Press the
increase, or the button to decrease the volume level.
6. MENU Button - Press to display the On-Screen menu
function.
7. SET – / + Buttons - Press to select the desired setting
during On-Screen operations.
8. RESET Button - Press to reset the On-Screen picture
adjustments to their factory preset positions.
9. TV/AV Button - Switches between TV and external inputs.
10. CALL Button - When you press this button, the channel
number will appear in the upper right corner of the screen.
Press the button again to remove display from the screen.
11. MUTE Button - To turn off the sound, press this button
once. The TV will be silenced and the symbol "MUTE" will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL
or button.
12. CH (CHANNEL) / Buttons - Press the
change to a higher numbered channel set into memory.
Press the button to change to a lower numbered channel
set into memory.
13. ENTER Button - Press to enter or select information for
On- Screen operations.
14. AUDIO SELECT Button - Switches sound between mono
and stereo when receiving broadcasts in stereo.
15. CH.1/2 Button - Switches between Channel 1 and Channel 2
in the Closed Caption mode.
16. TV/CAP/TEXT Button - Press this button to switch between
normal TV and the two Closed Caption modes (captions
and 1/2 of full screen text). Closed Captioning will display
text on screen for hearing impaired viewers.
Use two "AAA" size batteries. The batteries may last
approximately one year depending on how much the remote
control is used. For best performance, it is recommended
that batteries should be replaced on a yearly basis, or when
the remote operation becomes erratic. Do not mix old and
new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture (follow battery
manufacturer's directions).
2/21/05, 19:16
button to
button to
5