Victron energy Phoenix Charger 12/30 Manual De Instrucciones página 9

Adjustments with remote panel Phoenix
Charger Control
WARNING: Always check with your battery
supplier if the choosen charge characteristic
is suitable for your battery and application
• Remove the frontplate and connect the
Phoenix Charger Control panel to the 8-pin
modular jack.
• Disconnect battery, Voltage sense and
Temperature sense. A voltmeter is not required
but may be useful.
• While switching on keep one of the
pushbuttons ⇑ & ⇓ pushed.
• Release pushbutton.
• The adjust knob on the remote panel controls
the adjust-mode; the LED's on the charger
correspond with the knob as follows:
knob adjust mode
0% not impl.
10% Bulk
20% Absorption
30% Float
40% Rep. Abs. interval
50% Rep. Abs. time
60% Max. Abs. time
70% Characteristic
80% Battery type
90% not impl.
100% not impl.
• Push ⇑ for up and ⇓ for down.
• LED indicators on remote panel read the
value as follows:
LED flashing =
LED on =
1 bar flashing =
Left bar is [step x10], right bar is [step x1].
To read the Float and Absorption adjustment the
lowest value in the table has to be added:
12 V models
Bulk 0 – 50 A/30A;step 1A 0 – 25 A / 16 A; step 1 A
Abs 12.00 – 16.00 V;
step 0.1 V
Float 12.00 – 16.00 V;
step 0.1 V
Rep. Abs. int. 0 – 45 days; step 1 day ; def.= 7 days
Rep. Abs. time 0 – 72 qu. of an hour; step 1 qu.; def = 4 qu.
Max. Abs. time or 1 – 8 hrs ; default = 4 hrs.
Fixed Abs. time
Characteristic 1 = Fixed: Fixed Abs. time. default = 4 hrs.
Rep. Abs. int. default
Rep. Abs. time. default = 2 qu.
2 = Adaptive
3 = Adaptive with BatterySafe mode (default)
1
The optimum absorption voltage of flat plate lead acid batteries depends on mechanical and chemical properties. Batteries with high antimony
doping can general be charged with a lower absorption voltage than batteries with low antimony doping, like the Victory carbon fibre battery.
(See the book "Electricity on board" at
charger LED's
Failure
Failure Bulk
Failure Absorption
Failure Float
Failure Abs./Float
Failure Bulk/Abs.
Failure Bulk/Float
Failure Bulk/Abs./Float
Failure/Abs. Float
Failure
Failure
1 step
2 steps
9 steps
24V models
24.00 – 32.00 V;
step 0.1 V
24.00 – 32.00 V;
step 0.1 V
= 1 day
www.victronenergy.com
Battery type Abs. Voltage
default = 1
0: User defined
1: Sonnenschein 14.4 V 28.8 V 13.8 V/
Dryfit A200 gel
2: Traction 15.0 V 30.0 V 13.8 V/
(tubular plate)
1
3: Semitraction 14.4 V 28.8 V 14.0 V/
1
4: Victory 14.8 V 29.6 V 14.0 V/
12V
model
• Turn the knob to another adjust-mode to store or
switch Off to escape.
• Switch Off and On to start normal charging
sequence.
• Replace the frontplate.
10
Max. Bulk current =
25 amps
30
Float voltage =
12+(1x1)+(4x0.2)= 13.8 volts (12V model)
24+(1x1)+(4x0.2)= 25.8 volts (24V model)
Repeated Absorption time =
4 quarters of an hour
Characteristic =
1. Fixed mode
Warning: If the knob is not turned after an
adjustment the charger will not store this
adjustment. If the Float or Absorption voltage
was adjusted and the charger is not switched off
this voltage will remain on the outputs.
)
victron energy
Float Voltage / Max.Abs. time
Reduced Float
27.6 V/
13.0 V 26.0 V
27.6 V/
13.0 V 26.0 V
28.0 V/
13.0 V 26.0 V
28.0 V/
13.0 V 26.0 V
24V 12V 24V
model model model
Absorption voltage =
12+(1x2)+(2x0.2)= 14.4 volts (12V model)
24+(1x2)+(2x0.2)= 26.4 volts (24V model)
Repeated Absorption interval
50
Maximum Absorption time =
70
4 hrs.
6 hrs.
5 hrs.
5 hrs.
20
40
= 7 days
60
4 hrs.
80
Battery type =
1. Gel
8