Function Descriptions - Gemini UX-16M Manual Del Operador

Sistemas de frecuencia uhf profesionales del micrófono
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INTRODUCTION:
Congratulations on your purchase of a GEMINI wireless system. This
state of the art unit includes all the latest features backed by a three
year limited warranty. Prior to use, we suggest that you carefully read
the instructions.
SYSTEM FEATURES:
UX-16 M includes UX-16 receiver & XM-16 handheld microphone
UX-16 H includes UX-16 receiver, XB-16 body pack transmitter & HSM-1 headset
UX-16 L includes UX-16 Receiver, XB-16 body pack transmitter & LAV-1 lavalier
16 band UHF synthesizer controlled frequencies
Phase locked loop (PLL) circuitry
Super high sensitivity with extremely low noise transmission & reception
Stable & quality SMT assembled PCB module
XM-16 has a uni-directional dynamic microphone
HSM-1 has an electret condenser unit microphone
LAV-1 has an electret condenser unit microphone
CAUTIONS:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. THERE ARE
NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a
qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. Dust, dirt and debris can interfere with the performance of this unit. Make
an effort to keep the unit away from dusty, dirty environments, and cover
the unit when it is not in use. Dust it regularly with a soft, clean brush.
5. When moving this equipment, it should be placed in its original carton
and packaging. This will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES.
8. REMEMBER, ANY CHANGES MADE TO THE UNIT WITHOUT
AUTHORIZATION FROM GEMINI WILL VOID YOUR WARRANTY.
FCC RULES AND REGULATIONS:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1)This device may not cause harmful
interference and (2) This device must accept any interference received,
including interference that may cause undesired operation
Notice: The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
Important note, to comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user's authority to operate the device.
UX-16 WIRELESS SYSTEM:
The UX-16 wireless system is a high quality audio product that provides
excellent performance under most operating conditions. The different
systems available all operate on a UHF high band frequency between
USA: 682 ~ 698 MHz
Euroupe: 863 ~ 865
WIRELESS NOTES:
• Before setting up, make sure that the transmitter and receiver are tuned
to the same frequency.
• Do not use two transmitters in the same frequency. Use good quality
batteries to avoid the damage resulting from a defective leaking battery.
• Turn the volume control on the receiver to adjust receiver output level to
match input level requirements of an audio mixer or amplifier.
• While checking sound, move the transmitter around the area where you
use the system to look for dead spots. If you find any dead spot, change
the receiver position. If it does not work, avoid such places.
• To avoid interference, do not put the receiver too near metal object and
avoid obstructions between transmitter and receiver.
• Avoid the interference from TV, radio, other wireless appliances and etc.

FUNCTION DESCRIPTIONS:

UX-16 RECEIVER:
This is a stationary receiver for use with our 16-channel selectable
transmitters. The receiver operates in UHF band frequency with PLL
synthesized control. Powered by 12V DC.
(1) POWER INDICATOR: The indicator LED lights when the receiver is ready to operate.
(2)RF LEVEL INDICATORS: This LED lights to indicate that signal is being received.
(3) LEVEL CONTROL: This rotary control adjusts the receiver's output level from the
microphone to line level for matching the input sensitivity of the mixer or amplifier.
(4) ANTENNA: Fixed-length UHF antenna permanently mounted either on
the front or on rear panel.
(5) UNBALANCED OUTPUT: Unbalanced 1/4" mono jack audio output
provides unbalanced low-impedance output
(6) SQUELCH ADJ.: The squelch adjusts the output level to prevent from
the external noise. Setting the squelch too high will reduce the range of
the system. Set the squelch to minimum before turning the receiver on.
(7) CHANNEL SELECTOR: 16 different selectable frequencies as below.
(8) DC JACK: DC input connector for the supplied AC adapter.
XM-16 HANDHELD MICROPHONE:
The handheld microphone operates in UHF band frequency with PLL
synthesized control. UHF 16 preprogrammed selectable frequencies to
avoid interference. Uni-directional dynamic or uni-directional electret
condenser capsules with different characters for various choices. Use
1.5V x 2 AA size batteries for low operating cost.
(1) GRILLE: Protects the microphone capsule and helps reduce breath
sounds and wind noise. The grille for the various microphone capsules
differ in appearance.
(2) LOW BATTERY LED: LED indicates battery status. Switching the power
to "ON", the LED flashing once indicates that the transmitter has
sufficient power. If the LED stays on, it indicates that the battery has
insufficient power and should be changed soon. If the status LED fails to
flash, the battery is either dead or not positioned correctly, and you
should correct the positioning or change the battery.
(3) ON/OFF SWITCH: Turns transmitter power on and off.
(4) BATTERY COMPARTMENT: Insert two AA batteries into the
compartment and make sure that the polarity of batteries is correct.
(5) CHANNEL SELECTOR: Changes transmitter channel setting.
(6) BATTERY COVER: Push to expose battery compartment and channel selector.
(7) ANTENNA: Built-in high gain helical antenna.
XB-16 BODYPACK TRANSMITTER:
The bodypack transmitter operates in UHF band frequency with PLL
synthesized control. UHF 16 preprogrammed selectable frequencies to
avoid interference. Various uni-directional electret condenser capsule
options. Use 1.5V x 2 AA size batteries for low operating cost.
(1) CONNECTOR: 1/8" miniplug microphone connector
(2) ON/OFF SWITCH: Turns transmitter power on and off.
(3) LOW BATTERY LED: LED indicates battery status. Switching the power
to "ON", the LED flashing once indicates that the transmitter has
sufficient power. If the LED stays on, it indicates that the battery has
insufficient power and should be changed soon. If the status LED fails to
flash, the battery is either dead or not positioned correctly, and you
should correct the positioning or change the battery.
(4) ANTENNA: Permanently connected, helical antenna.
(5) CHANNEL SELECTOR: Changes transmitter channel setting.
(6) GAIN: The rotary control adjusts the sensitivity of the transmitter's audio
to the level of the connected lapel microphone or instrument.
(7) BATTERY COMPARTMENT: Insert two AA batteries into the
compartment and make sure that the polarity of batteries is correct.
SETTING UP:
Prior to setting up, check that the transmitter and receiver are tuned to
the same frequency. Two or above transmitters operating in the same
frequency can not be used at the same time and area, so please select
the different frequencies which can be used simultaneously at local area.
(4)
(4)
(4)
(4)
(4)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ux-16hUx-16l

Tabla de contenido