Before Use; Safety Instructions; Mechanical Installation - JB Systems Light MLS-20 Manual De Instrucciones

ENGLISH
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
 This device has been designed to produce decorative effect lighting and is used in light show systems.
 Multicolor plastic tubes with RGB LEDs, used to change the color of walls, ceilings, etc. in all kinds of
venues: bars, discotheques, taverns, shops, ...
 Infinite applications possible: fix the strips in cabinets, behind translucent plexi panels to create slowly
changing colored surfaces, ceilings and walls, ...
 Two-side adhesive tape for easy fixing included
 Can be fixed on any surface using small screws
 Elegant "slim line" design!
 Strips can be fixed without gaps between the units: no interruptions in the light output!
 No visible connection cables, they are completely hidden inside the units
 Available in 2 lengths: 20cm and 50cm
 To be used with our LED-MANAGER (DMX power supply)
 Long life LED Technology!

BEFORE USE

 Before you start using this unit, please check if there's no transportation damage. Should there be any, do
not use the device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
 Operating instructions
 MLS-20 (20cm) or MLS-50 (50cm)
 Two-side adhesive tape for easy fixing included
 Connection cable with 2 connectors (L=10cm)

SAFETY INSTRUCTIONS:

This symbol means: indoor use only.
This symbol means: Read instructions.
 To protect the environment, please try to recycle the packing material as much as possible.
 Do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
 This unit is for indoor use only.
 Don't place metal objects or spill liquid inside the unit. If a foreign object enters the unit, immediately
disconnect the installation setup from the mains power.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
JB SYSTEMS
®
OPERATION MANUAL
1/25 MLS-20 + MLS-50 MINI LED STRIP
ENGLISH
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don't use this unit at higher ambient temperatures.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
 The cables should always be in perfect condition: switch the LED Manager immediately off when the
cables are squashed or damaged.
 This appliance must be used with the LED Manager: don't connect the unit to any dimmer pack or other
power supply.
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 The housing must be replaced if it is visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Don't use the effect in the presence of persons suffering from epilepsy.
DESCRIPTION:
1. LED Strip enclosure
2. PCB with high power LEDs: can be pulled out of the U-shaped base to make installation easier.
3. Input connector (mounted on the bottom side): to be linked with the LED manager or with the output of a
previous LED strip in the chain.
4. Output connector (mounted on the bottom side): to be linked with the input of a next LED strip in the
chain.

MECHANICAL INSTALLATION

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during installation and
servicing.
 Before installation make sure that the installation area can hold a minimum point load of 10times the
device's weight.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
Mounting with Two-side adhesive tape:
This is the easiest and fastest way but only possible on a smooth surface!
 Cut the tape at the right size.
 Put it on the bottom or side of the U-shaped enclosure as shown on the drawings.
JB SYSTEMS
®
OPERATION MANUAL
2/25 MLS-20 + MLS-50 MINI LED STRIP