Figura 28. Conjunto De La Carcasa Del Afilador; (Vista Trasera, Armada) - EASTMAN BLUE STREAK II Manual De Instrucciones

EASTMAN
Sharpener Housing
Assembly
(Rear View)

Figura 28. Conjunto de la carcasa del afilador

(Vista Trasera, Armada)

Nota: Especifique el modelo y número de serie
de su máquina al solicitar piezas.
30
Form C-1555S
Part No. No. Req'd
For both
627 & 629
4C2-2 1
4C2-85 1
4C2-86 1
11C12-58 1
11C12-59 1
11C12-81 1
11C12-85 1
11C12-56 1
11C12-57 1
11C12-80a 1
11C12-84 1
11C12-64 1
12C11-74 1
12C15-29 2
12C15-30 2
17C15-78 1
17C15-103 1
17C15-113 1
18C6-81 1
18C6-26 1
34C10-89 1
55C4-41 1
62C16-151 1
65C6-75 1
71C1-10 1
73C7-46 1
73C7-47 1
73C7-86 1
73C7-88 1
73C7-48 1
73C7-49 1
73C7-85 1
73C7-87 1
79C12-163 1
85C3-6E 1
87C3-8 1
87C3-44 2
87C3-53 1
90C4-29 1
90C4-33 2
90C4-34 1
90C4-42 1
90C4-48 1
90C4-58 1
90C6-24 2
142C1-7 1
191C1-21 1
300C7-1 1
300C10-1 2
302C10-6 1
302C12-3 3
584C2-3 1
584C3-16 1
602C1-7 1
602C1-9 1
627C1-10 1
716C1-12 1
727C1-6 1
Description
Lock Nut for Shaft
R.H. Follower Nut
L.H. Follower Nut
R.H. Square Shaft 5"-8" Knife
R.H. Square Shaft 9"-10" Knife
R.H. Square Shaft 11-1/2" Knife
R.H. Square Shaft 13" Knife
L.H. Square Shaft 5"-8" Knife
L.H. Square Shaft 9"-10" Knife
L.H. Square Shaft 11-1/2" Knife
L.H. Square Shaft 13" Knife
Shaft for Crank
Thrust Washer
Thrust Washer
Thrust Washer for Bottom Plate
Pin for Bell Crank
Roll Pin for Push Rod
Spreader Pin
Retaining Ring for Shaft
Retaining Ring for Bell Crank
Spring for Bell Crank
Spacer for Ball Bearings
Sharpener Housing (Only)
Push Rod
Oil Retainer-Idler Gear
Tube for Square Shaft 5"-8" Knife
Tube for Square Shaft 9"-10" Knife
Tube for Square Shaft 11-1/2" Knife
Tube for Square Shaft 13" Knife
Tube for Screw Shaft 5"-8" Knife
Tube for Screw Shaft 9"-10" Knife
Tube for Screw Shaft 11-1/2" Knife
Tube for Screw Shaft 13" Knife
Bottom Plate, Sharpener Housing
Bell Crank (Only)
Spiral Gear
Spur Gear
Gear and Shaft
Bearing for Drive Shaft (Lower)
Bearing for Gears
Bearing for Bell Crank
Bearing for Drive Shaft
Bearing for Drive Shaft (Upper)
Bearing for Screw Shaft
Ball Bearing for Crank
Key for Gear
Felt Pad for Cross Head
Screw, #4-36 x 1/8 Round Head
Screw, #6-32 x 3/16 Round Head
Screw, #6-32 x 1/2 Flat Head
Screw, #8-32 x 3/8 Flat Head
Bell Crank with Pin & Bearing (Only)
Bell Crank Complete with Lever
Slow Speed Driver Assembly
Driver Pulley with Driver
Idler Gear & Bushing
Driver Shaft with Gear
Oil Pad & Holder