Digital Effects Table; Digital Effect Processor; Master Section - Phonic CELEUS 800 Manual Del Usuario

Digital Effect Processor

33. Program Control
This control will allow users to select one of the 16 built-in digital
effects of the CELEUS. The effect names that correspond with the
numbers can be found on the top of the mixer's face, or in the
digital effect table.
34. Effects On Button & LED
Pushing this button will turn the built-in effect processor on and off.
When the effect processor is activated, the corresponding LED will
light up to indicate so.
35. Parameter Control
Turning this control will adjust the one main parameter of the
selected effect. Each effect's parameter can be found on the digital
effect table.

Master Section

36. 2T Return/USB Control
This control adjusts the incoming signal from both the RCA "2T
RTN" jacks and the onboard USB interface. The signals are then
sent to the main mix. The "To CTRL RM" button allows the signal
to be sent to the Control Room / Phones mix.
37. Graphic Equalizer
This graphic equalizer allows you to adjust the frequency response
of your main signal, with a maximum of ±12 dB of signal boost or
cut for each of the 9 frequency bands. The button provided along
with the Graphic EQ allows it to be activated and deactivated.
36 33
38. +48V Indicator
This LED indicator will light up when Phantom Power is activated
on microphone inputs.
39. Power Indicator
This LED indicator illuminates when power of your CELEUS 800
mixer is activated.
40. Level Meter
These dual 12-segment level meters give an accurate indication
of when audio levels of the Main L/R output signals reach certain
levels. The 0 dB indicator illuminates is approximately equal to an
output level of +4 dBu, and the PEAK indicator illuminates about 6
dB before the signal is dynamically clipped. It is suggested for the
maximum use of audio to set the various levels controls so that it
sits steadily between 0 and 8 dB to make full use of audio, while
still maintaining fantastic clarity.
When any of the solo buttons are pushed in, the level meter will
then display the audio properties of the Control Room / Phones
mix. This is especially helpful when setting the levels of each
individual channel, as is shown in the Channel Setup section of
this manual. The "Solo" LED will illuminate when the Level Meter
displays the audio properties of the Control Room / Phones signal.
6
41. Control Room / Phones Controls
This control is used to adjust the audio level of the phones feed,
as well as the signal sent to the Control Room output. This is for
use in monitoring, as side fill, or for the addition of additional audio
gear. The Pre/Post buttons alternates the Control Room / Phones
source signals between those of post-fader and pre-fader feeds.
The main mix will typically be sent to the Control Room / Phones
mix unless any SOLO buttons are pressed. In this instance, the
SOLO signal(s) will be sent to the Control Room / Phones mix.
42. AUX Send Master Controls
These controls adjust the final level of the AUX mixes (as taken
from the AUX level controls on each channel strip), the audio of
which is sent to corresponding AUX send outputs. The SOLO
button that accompanies these controls allows you to send the
AUX Send signal to the Control Room / Phones mix. The AUX 1
send control is a fader while the AUX 2 send is a rotary control.
43. EFX Send Master Control
This control adjusts the final level of the EFX mix (as taken from
the EFX level controls on each channel strip), the audio of which is
sent to the AUX Send 3 outputs, as well as the built-in digital effect
processor. The corresponding SOLO button allows you to send the
signal to the Control Room / Phones mix.
44. AUX RTN Controls
This control adjusts the signal level of audio fed through to the
35 stereo AUX Return inputs, which will be added to the main mix.
The "To AUX 1" control adjusts the pre-fader level of the signal
from the AUX Return control to the AUX 1 mix (also known as
"EFX to Monitor").
34
37
43
45
42
44 42 41 38
39
40
47
46
CELEUS 800