Bluetooth Setup; Usb Playback; Usb Recording; Audio Interface - Phonic CELEUS 800 Manual Del Usuario

BLUETOOTH SETUP

1. Push the Bluetooth button to turn the Bluetooth on
2. Enter your laptop, cell phone or tablet's Bluetooth setup options
to find the "Phonic.BT" Bluetooth device.
3. If requested, the password for the CELEUS 800's Bluetooth
function is 0000. A lot of modern smartphones will enter this as
the default password.
4. Audio signals received through the Bluetooth interface will be
routed to channel 11/12 on the mixer.
5. To reset the connection, turn your laptop, cell phone or tablet's
Bluetooth connection off and then on again.
6. When using cell phones and tablets, it may be an idea to turn
"Airplane Mode" or "Flight Mode" on to stop phone calls or push
notifications from interrupting your audio.
Note: Not all modern Bluetooth-enabled devices allow for use of external
audio playback. In the case of laptops in particular, Bluetooth may be used
for data transmission only - depending on the model. This is a limitation of
these devices and you will not be able to use the CELEUS 800's Bluetooth
function with these devices.

USB PLAYBACK

1. Power on the device.
2. Insert an appropriately formatted (FAT32) USB flash drive.
3. Press the PLAY button to play the current track, or the << and
>> buttons to skip forward and backwards between tracks.
4. The CELEUS 800 can playback MP3 and WMA files.
5. Use the level control for channel 13/14 to adjust the USB
player's volume.
6. Press the STOP/MENU button to access the File Browser
(Folders) and Repeat Mode functions.
Folders – Freely navigate songs in each folder on USB flash disc
using the << and >> buttons. Press PLAY button to select, press
MENU button to go back.
Repeat Mode – There 4 repeat modes available.
No Repeat – Play each file in the current folder or root once.
Repeat One – Continuously repeat selected song.
Repeat Folder – Continuously repeat all the song in the current
folder or root directory.
Random – Enables random playback of files in current folder or
root.

USB RECORDING

1. Power on the device.
2. Insert an appropriately formatted (FAT32) USB flash drive.
3. In the main menu, select "Record" and press the PLAY button
to enter recording mode.
4. Select between the 128 kbit/s and 192 kbit/s WAV recording
modes and press the PLAY button.
5. Record mode will begin in standby/pause. Push the Play/Pause
button to begin recording. The unit will save the recorded file
into the RECORD directory on the USB device.
6. Push the Play/Pause button to pause recording. Pushing
the Play/Pause button again will resume recording from the
position at which it was paused.
7. Press the MENU button at any time to save the recording. Once
the recording is saved, additional audio cannot be recorded to
that file.
8. To exit record mode and return to the main menu, press and
hold MENU button for three seconds.
2

AUDIO INTERFACE

By simply connecting the USB cable provided along with your
CELEUS to the device and your personal computer or laptop,
you are able to send CD quality (16-bit stereo, with a 44.1 kHz
sampling rate) signal to and from your mixer. By doing this, you are
actually turning your CELEUS 800 into a highly useful plug'n'play
soundcard for your computer.
The USB sends an audio stream of the Main Left and Right (record
out) signal of your mixer to the computer. You can use almost any
dedicated Digital Audio Workstation (DAW) software to record the
signal from the CELEUS mixer. You can also set the mixer as your
default audio device.
The USB interface also returns the audio signal from your computer
back to the 2T Returns, the signal of which is controlled by the 2T
/ USB Return control. If there are input signals from both the USB
interface and the 2T Return, the two signals are combined and
controlled simultaneously by the 2T return control.
Windows
1. Turn on both the CELEUS and the computer.
2. Connect the CELEUS mixer to the computer via the provided
USB cable.
3. Let Windows find the device and install an appropriate driver.
4. Enter the Control Panel and select Sounds and Audio Devices.
5. When here, go to the Audio tab and select the "USB Audio
Codec" as your default sound recording and playback device.
6. Depending whether you have Windows XP, Vista, 7, 8 or 10,
this may differ slightly, but the setting can always be found
within the Control Panel's audio menu.
7. If you don't want to use the CELEUS as your default audio
device, you can simply enter your DAW or other audio program
and select it as your default device in the program only.
8. Be sure to set your minimum buffer settings to 64 samples as
to avoid clicks and pops.
Mac
1. Turn both the CELEUS and the computer on.
2. Connect the CELEUS mixer to the computer via the provided
USB cable.
3. Enter the AUDIO MIDI SETUP menu.
4. Select the "USB Audio Codec" as your input and output device.
5. The CELEUS is now your default audio device.
6. Alternatively, enter your DAW software (or other relevant audio
program) and select the "USB Audio Codec" in the device
preferences.
7. Be sure to set your minimum buffer settings to 64 samples as
to avoid clicks and pops.
CELEUS 800