For Your Safety - PLA.NET PLA-GL40 Manual De Instrucciones

• BURNER: loosen the screw, remove it and fasten it back again.
• SPARKING PLUG: loosen the screw that fixes the sparkling plug and remove the cable.
• TAP: Remove the rubber support on the back, loosen the support/ramp, extract the ramp by approximately 2 cm. Unscrew the tap and replace it with a new one, ensuring is
it gas tight (use a threadlocker or gas Teflon tape)
THE MANUFACTURER DENIES ANY RESPONSIBILITY DUE TO IMPROPER USE OR INCORRECT INSTALLATION OF THE APPLIANCE.

FOR YOUR SAFETY

• Note the model given on the data plate as:
• PLA-GL models are only equipped to be supplied with BUTANE or PROPANE.
• PLA-GM models are only equipped to be supplied with METHANE.
• Devices are delivered and provided as indicated in the label. Once the connection to the relative gas is completed it's not necessary perform any adjustment on
the device.
• The appliance and the cylinder must be located on a flat base and sheltered from the wind. Make sure that inflammable materials are not in the area surrounding the
appliance.
• Protect the cylinder from sunrays.
• Cylinders must not be kept in the home, in places where there is no air ventilation, or in places below ground level.
• WARNING: do not move the appliance while it is in operation or when it is still hot even if it has wheels.
• Ruined or porous gas connection pipes must be replaced, just as they should if the date stamped on them has expired.
• Flexible hoses must not be pulled, squeezed or be in contact with hot surfaces.
• Maintenance and repair work must only be carried out by authorized and qualified personnel.
• Any alterations or tampering can create a hazard.
• Hotplates/grills reach high temperatures during the cooking stage. Be careful!
• Do not wash or wet the hotplate/grill with water when it is hot, it could cause the cooking top deformation.
• Make sure you keep the cylinder away from the appliance when it is in use.
THIS APPLIANCE IS ONLY FOR OUTDOOR USE.
The air required for combustion is 2.0m 3 / h for each kW of installed thermal capacity (1 KW = 3412 BTU).
WARNING: APPLIANCE PARTS THAT ARE ACCESSIBLE DURING OPERATION ARE VERY HOT, THEREFORE WE RECOMMEND THAT CHILDREN ARE KEPT AT A
DISTANCE
IF YOU CAN SMELL GAS:
1) Shut off the gas supply to the appliance;
2) Extinguish any live flames;
3) If the smell continues, contact your gas supplier.
STRUCTURAL SPECIFICATIONS
- The appliance is made of stainless steel.
- The burners are atmospheric.
- The appliance is delivered complete and finished from the manufacturer; it does
not require special assembly when installed.
- Appliance models are as follows:
Model
PLA-GL40
PLA-GM40
PLA-GL40T
PLA-GM40T
PLA-GL55
PLA-GM55
PLA-GL55PL
PLA-GM55PL
PLA-GL60
PLA-GM60
PLA-GL70T
PLA-GM70T
PLA-GL80
PLA-GM80
PLA-GL80PL
PLA-GM80PL
PLA-GL26/55
PLA-GM26/55
N°
Ø nozzle
Burners
1/100 mm
2,8 kW
1 80
1 130
1 80
1 130
2 80
2 130
2 80
2 130
2 80
2 130
2 80
2 130
3 80
3 130
3 80
3 130
3 80
3 130
Model with Fry-Top hotplate
Dimensions Power
W x D x H mm (kW)
370 x 435 x 180 2,8
370 x 435 x 180 2,8
370 x 532 x 180 2,8
520 x 370 x 180 2,8
530 x 435 x 180
5,6
530 x 435 x 180 5,6
536 x 432 x 180 5,6
536 x 432 x 180 5,6
600 x 435 x 180 5,6
600 x 435 x 180 5,6
680 x 532 x 180 5,6
680 x 532 x 180 5,6
790 x 435 x 180 8,4
790 x 435 x 180 8,4
791 x 432 x 180 8,4
791 x 432 x 180 8,4
806 x 432 x 180 8,4
806 x 432 x 180 8,4
Model with lava stone grill
Consumption gas
G20 G25 G30
m3/h m3/h g/h
204
0,267 0,310
204
0,267 0,310
408
0,534 0,620
408
0,534 0,620
408
0,534 0,620
408
0,534 0,620
611
0,800 0,931
611
0,800 0,931
611
0,800 0,931
GB
G31
g/h
200
200
400
400
400
400
600
600
600