Water Supply; Miscellaneous; Preparatory Work And Installation Box; S 3004 / S 3004 P - Truma S 3004 Instrucciones De Montaje

Water supply

When installing a water supply into the vehicle, please ensure
that there is an adequate distance between the water hoses
and the heat source (e.g. heater, warm air duct).
A water hose may only be fitted at a clearance of 1.5 m to the
heater on the warm air duct. The Truma hose clip SC (part no.
40712-01) can be used if this distance is observed. In the case
of parallel installations, e.g. openings through a wall, a spacer
element should also be attached (e.g. insulation) to prevent
contact.

Miscellaneous

When installing a perforated drawer above a heater, i.e. for
drying objects, an intermediate shelf (minimum depth 280 mm
or 380 mm for S 5004) made of uncoated wood) is required.
Covers in the installation area must be made of a temperature-
resistant material (no PVC or similar).
If the vehicle is provided with an under-chassis guard, all heat-
ing parts under the car must be covered so that the produced
spray mist cannot lead to heating system malfunctions. Re-
move the covers again after finishing work.
In order to achieve a quick distribution of warm air and
reduction of the surface temperature on the outlet grill of
warm air, we recommend the installation of a Truma fan TEB-3
or TN-3. The S 5004 heating must be equipped with at least
one fan. A special installation box is available for operation
with two fans.

Preparatory work and installation box

For the unit to work perfectly, it is important that the low-
er edges of the installation box and the heating bees are
at one level and that the base is positioned in accordance with
the installation template so that the control knob is neither too
high nor too low.
Fix the installation template on the floor of the installation
cut-out, the arrow must point exactly to the front edge of the
cut-out (R = right installation, L = left installation).
Saw out the floor cut-out and pre-punch the 5 points for the
fixing screws.
Fig. A (right installation) / fig. B (left installation)
Insert the halves of the frame (4) into the floor cutout, push
outwards and screw tight (you may also want to bend the legs
out beforehand so that the frame fits well).
Break the pre-punched recesses for the exhaust duct on the
installation box (1) (R = right installation, L = left installation).
If the installation depth is low, the exhaust duct can also be
guided to the side on the S 5004 heating (R1 or L1).

S 3004 / S 3004 P

1
T
R
U
L
If a Truma fan and / or the additional electric heater,
Truma Ultraheat, is mounted, remove the cover (T or U)
and pre-mount them in accordance with the respective en-
closed installation instructions on the installation box.
S 5004
1
T
R1
U R
L1
L
S 3004 / S 3004 P
– Fix the fan (20) with 3 screws (3.5 x 19) to the installation
box.
– Place the supports (60) onto the nozzles (1a) of the installa-
tion box and click in place.
Internal control panel
– push the control panel cable (23 – silicone) for the fan
through the recess in the support and clamp in the foreseen
cable guide.
External control panel
– the control panel cable (not illustrated) may not against the
heating, the fan or hot air pipe. Fix the cables sufficiently.
– Fix the installation box (1) in the installation cut-out with
6 screws (3 x 12) inclined outwards. If this is not possible,
the installation box can be fixed at the side on the top end
of the installation cut-out with 4 screws.
– Fix the support (60) with 3 screws (3.5 x 16).
– Place the blend (61) on the 2 centering aids (60a) on the
support. Pivot from above until it clicks in.
1a
1
3 x
2 x
3 x
23
60
60a
7
60
61
20
2x
1a
20
23
3 x
3 x
1a
15