Important; Tool Use And Care; Specific Safety Rules For - Urrea CC904 Manual De Usuario

IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
Do not use tools if switch does not turn it on or
off. Any tool that cannot be controlled whith
the switch is dangerous and must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and diferential switch
when you are using an electric equipment.
E N G L I S H •
SERVICE
Tool service must be perfomed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.

SPECIFIC SAFETY RULES FOR

MARBLE CUTTERS
1. Keep hands away from the cutting blade
and the cutting area, never put your hands
under the workpiece, the disc spins under the
workpiece and putting your hand near the cut-
ting area will increase the risks of accidents.
2. Do not hold the material to be worked in
your hands or put it on your leg, it's impor-
tant that the material be adequately clamped
down, reducing the contact with the body and
the possibility of losing control of the equip-
ment.
3. Hold your tool by the handle when work-
ing. Do not operate the tool on surfaces un-
der which there might be electrical wires, and
water or gas pipes. The contact with electrical
wires or water might cause electrical shocks.
The electric motor generates sparks that, if in
contact with flammable gases, might cause ex-
plosion.
4. Always use blades of correct sizes and with
round holes. Blades with shapes that don't
match the backing flange on which they'll be
assembled will work in an irregular way, caus-
ing loss of control of the tool.
5. Never use damaged or incorrect bolts or
washers, the ones that come with your tool
were specially manufactured for your grinder,
so that they provide the best performance and
guarantee the safe operation of the equip-
ment.
6. Never plug or unplug the tool from the
power outlet if either the plug or the power
outlet is wet. First turn off the circuit (circuit
breaker or fuse) that energizes the tool. Then,
remove the plug from the power outlet and
check the plug and the power outlet for pres-
ence of water.
7. Wait for the blade to come to a complete
stop, note that there is a period of inertial
movement before the tool stops, after it's
turned off.
8. Use only accessories that are designed and
compatible with the speed informed on the
tool and in this manual.
U se r's m a nua l
9