Briteq BT-575W Manual De Instrucciones página 5

ENGLISH
4. REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is used in
standalone or master/slave mode.
5. SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or
master/slave mode.
6. DMX INPUT/OUTPUT: used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link
the units together.
MAIN MENU:
 To select any of the pre-set functions, press the MENU button up to when the required one is shown on
the display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to change the mode.
 Once the required mode has been selected, press the ENTER button to select. After 8 seconds the display
will automatically return to the main functions without any change. To go back to the functions without any
change press the MENU button. The main functions are shown on the right.
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until
is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512
address.
 Once the correct address shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions without
any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Channel Mode
 Press the MENU button until
is shown on the
display.
 Press the ENTER button so the display
blinking.
 Use DOWN and UP button to select the
Channel ) or (8 Channel) mode.
 Once the mode is selected, press the ENTER button
to setup
( or automatically return to the main functions
without any change after 8 seconds. )
To go back to the functions without any change
press the MENU button again.
Show Mode
Used to choose the Show mode when used in
standalone or master/slave mode.
 Press the MENU button until
is showing on
the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
4) mode.
 Once the right mode shows on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
BRITEQ
®
OPERATION MANUAL
starts
(16
(show 1), (show 2), (show 3) or
5/68 BT-575W
ENGLISH
Show 1 mode- Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode-Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on a podium, in front of the audience
The spot is always projecting to the audience's direction; i.e in front of the stage. Pan movement
angle (left to right to left ): 160°. Tilt movement angle: 90° ( 60° above horizon; 30° below horizon.)
Show 4 mode - Fixture is fixed under ceiling.
The spot is mainly projecting in front of the stage. Pan movement angle ( left to right to left ) :160°.
Tilt movement angle: 90° ( vertically, front 75°; back 15° )
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the MENU button until
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
 Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
 Once the mode has been selected, press the ENTER button to save it.
(show
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
BRITEQ
®
OPERATION MANUAL
is shown on the display.
(normal) or (2 light show) mode.
is shown on the display.
(yes blackout) or (no blackout) mode.
is shown on the display.
(normal) or (pan inversion) mode.
is shown on the display.
(normal) or (tilt inversion) mode.
6/68 BT-575W