Specific Safety Rules - Ryobi RLS1351 Manual Del Operador

 KEEP hANDS AwAy FROM CUTTiNg AREA. Do not
reach underneath work or in blade cutting path with hands
and fingers for any reason. Always turn the power off.
 ALwAyS SUPPORT LONg wORKPiECES while cutting
to minimize risk of blade pinching and kickback. Saw may
slip, walk or slide while cutting long or heavy boards.
 ALwAyS USE ThE wORK CLAMP to secure the
workpiece when making cross cuts.
 BE SURE ThE BLADE CLEARS ThE wORKPiECE.
Never start the saw with the blade touching the
workpiece. Allow motor to come up to full speed
before starting cut.
 NEVER cut more than one piece at a time. DO NOT
STACK more than one workpiece on the saw table at a
time.
 NEVER PERFORM ANy OPERATiON FREEhAND.
Always place the workpiece to be cut on the saw table
and position it firmly against the fence as a backstop.
Always use the fence.
 NEVER hand hold a workpiece that is too small to be
clamped. Keep hands clear of the cutting area.
 NEVER reach behind, under, or within three inches of the
blade and its cutting path with hands and fingers for any
reason.
 NEVER reach to pick up a workpiece, a piece of scrap,
or anything else that is in or near the cutting path of the
blade.
NEVER move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade is
rotating. Any slip can result in contact with the blade
causing serious personal injury.
 AVOiD AwKwARD OPERATiONS AND hAND
POSiTiONS where a sudden slip could cause your hand
to move into the blade. ALwAyS make sure you have
good balance.
 NEVER stand or have any part of the body in line with
the path of the saw blade.
 ALwAyS release the power switch and allow the saw blade
to stop rotating before raising it out of the workpiece.
 DO NOT TURN ThE MOTOR SwiTCh ON AND OFF
RAPiDLy. This could cause the saw blade to loosen
and could create a hazard. Should this ever occur,
stand clear and allow the saw blade to come to a
complete stop. Disconnect your saw from the power
supply and securely retighten the blade bolt.

SPECiFiC SAFETy RULES

 iF ANy PART OF ThiS SAw iS MiSSiNg or should
break, bend, or fail in any way, or should any electrical
component fail to perform properly, shut off the power
switch, remove the saw plug from the power source and
have damaged, missing, or failed parts replaced before
resuming operation.
 ALwAyS STAy ALERT! Do not allow familiarity (gained
from frequent use of the saw) to cause a careless
mistake. ALwAyS REMEMBER that a careless frac-
tion of a second is sufficient to inflict severe injury.
 iF ThE POwER SUPPLy CORD iS DAMAgED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
 MAKE SURE wORK AREA hAS AMPLE LighTiNg to
see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
saw.
 ALwAyS TURN OFF ThE SAw before disconnecting it
to avoid accidental starting when reconnecting to power
supply. NEVER leave the saw unattended while connected
to a power source.
 TURN ThE SAw OFF. Wait for the blade to come to a
complete stop before removing the workpiece.
 ThiS TOOL should have the following markings:
a) Wear eye protection.
b) Keep hands and body out of path of saw blade.
c) Do not operate saw without guards in place.
d) Do not perform any operation freehand.
e) Never reach around or over saw blade.
f) Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
g) Disconnect power (or unplug tool as applicable)
before changing blade or servicing.
h) Return saw to rear of tool after each cross cut.
i) Use a push stick for narrow work and when
required.
j) Pay particular attention to instruction on reducing
risk of kickback.
 ALwAyS MAKE SURE ThE SAw BLADE hAS CLEAR-
ANCE OF ALL OBSTRUCTiONS BEFORE TURNiNg
ThE SAw ON.
 ALwAyS carry the tool only by the carrying handle.
 SAVE ThESE iNSTRUCTiONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
5