Know Your Product; Operation - RS Components 18410192476 Instrucciones De Uso

d To install the battery: Insert the charged battery into the
opening at the base of the power tool until the battery is
s securely latched with a click.
.
bAtteRy CHARGING
a
▪ Insert the plug of the charger in the socket. The green
LED on the charging indicator (11) will start to glow
d
thus indicating that the charger is in standby state.
k
▪ Insert the battery (5) in the charger socket (10) consid-
e
ering the polarity. (Fig. 1)
▪ A new battery will work properly after five cycles of
charging and discharging. Charge and discharge a
p
battery, which is not used for a long time, for two to
three times to function well.
e
▪ When the battery working time is remarkably short de-
–
spite full charging, the life of the battery may be over.
Replace the battery immediately.
,
o
y WARNING: The battery will be fully charged
r after approximately 30 min, remove it from the charger
e after this time.
-
-
Charging indication:
▪ The green LED starts to glow upon plugging the
y
charger in the mains.
y
▪ The green LED ceases to glow and the red LED lights
up after the battery has been placed in the charger,
,
thus indicating the beginning of the charging process.
m
During the charging process the charger and battery
-
might become warm. This is a normal condition, and
does not indicate a problem.
▪ After completion of charging which takes approxi-
mately 30 min, the red LED ceases to glow and the
green LED lights up.
The charger features thermal overload protection for the
battery. Nevertheless we recommend withdrawing the
battery from the charger upon expiring of the charging
-
time. You may use additionally an electric timer in order
-
to control the charging time.
R
tO ObtAIN tHe best lIfe fOR tHe bAtteRy
d
r
▪ When battery is not in use, keep it away from other
d
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
-
the battery terminals together may cause fire or ex-
r
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may drop
-
under 0ºC or exceed +40ºC.
e
bAtteRy stAte INDICAtION
The battery state during operation can be checked on
the LED display (7) by pressing the indicator button (6).
(Fig. 2)
Depending on the number of illuminated LEDs the bat-
tery state is as follows:
Original instructions
RS-754-1924-pages-BR2 10.8Li.indd 7
3 = Battery 100% - 60% charged.
2 = Battery 60% - 30% charged.
1 = Battery < 30% charged. It is necessary to recharge
the battery.
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
VII - Know your product
Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Keyless chuck
2. Speed selector switch
3. Forward/reverse switch
4. Battery release buttons
5. Battery
6. ON/OFF trigger switch
7. Battery state indicator
8. LED light
9. Torque adjustment collar
10. Charger
11. LED charge state indicator
VIII - Operation
leD WORK AReA lIGHt
The machine is equipped with LED light (8) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. To turn the LED light on and off de-
press the LED light button (6).
ReveRsING
The extreme position of lever (3) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (6) is depressed lever (3) can not be
actuated. (Fig. 3)
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
sWItCHING ON - sWItCHING Off
switching on: press ON/OFF switch (6).
switching off: release ON/OFF switch (6).
The power tool is equipped with a brake. The spindle
stops rotating immediately after releasing the switch le-
ver.
smOOtH eleCtRONIC RPm CONtROl
Light pressure on ON/OFF trigger switch (6) results in
low rotation speed, further pressing the switch results in
7
EN
8.6.2012 . 15:09:08 .