Compiling An Individual Title Sequence - Monacor M-10CD Manual De Instrucciones

5 Operation
After connection of the supply voltage the CD player is
switched on. If there is no CD in the player mechanism,
the display (3) shows "– –".
5.1 Playing a CD
1) Press the button "OPEN/CLOSE" (9). The CD draw-
er (1) opens. Insert a CD with the lettering facing
upwards. To close the drawer, press the button again.
After retracting the drawer, the CD player is set to
stop and the display shows the total title number of
the CD.
2) To start the first title, press the button "PLAY/PAUSE"
(7). To start with another title, select it with one of the
"SKIP" buttons (8) [see chapter 5.1.1] and start the
replay with the button "PLAY/PAUSE" as long as the
number of the selected title flashes in the display (3).
During the replay the yellow LED "PLAY" (2) lights up.
With the button "PLAY/PAUSE" it is possible to
change between replay and pause. In the pause
mode the LED "PLAY" flashes.
3) After playing the CD or after pressing the button
"STOP" (4), the LED "PLAY" will be extinguished and
the CD player will switch to the stop mode.
4) After each operation always retract the CD drawer
with the button OPEN/CLOSE to protect the laser
system against impurities.
5.1.1 Title selection/Fast forward and reverse
While replaying or in the pause mode it is possible to se-
lect another title with the "SKIP" buttons (8) or to fast for-
ward or reverse on the CD.
Title selection
With each pressing of the button "F.SKIP" the unit
goes to the next title.
By pressing the button "B.SKIP" once, the unit goes
to the beginning of the currently playing title. By
pressing this button several times, the unit always
reverses one title.
Fast forward/reverse
For the fast forward of the CD keep the button
"F.SKIP" pressed, for the fast reverse keep the button
"B.SKIP" pressed. The fast forward/reverse also
goes beyond several titles, however, it stops at the
end and at the beginning of the CD.

5.2 Compiling an individual title sequence

1) For the title programming the CD player must be set
to stop, if necessary, press the button "STOP" (4).
2) Press the button "PROG" (5). The yellow LED "PRO-
GRAM" (2) and the display (3) flash.
3) With the button "B.SKIP" or "F.SKIP" (8) select the
first title for the desired title sequence.
4) Press the button "PROG" (5).
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
5) Repeat the operating steps 3 and 4 for all further de-
6) To start the title sequence, press the button "PLAY/
7) After playing the title sequence or after pressing the
8) As long as the CD player is not switched off or the CD
5.3 Switching on the repeat function
1) For permanent repeat of a title, press the button
2) For continuous repeat of the entire CD or of an indi-
3) To switch off the repeat function, press the button
6 Maintenance
Protect the CD player module against dust, vibrations,
direct sunlight, humidity, and heat (admissible ambient
temperature range 0 – 40 °C). For cleaning only use a
soft, dry cloth, by no means water or chemicals.
Note on sound interruptions and reading errors
Cigarette smoke easily penetrates through all openings
of the unit and settles on the optics of the laser system.
This deposit may cause reading errors and sound inter-
ruptions. As cigarette smoke cannot always be avoided
(e. g. in a discothèque), the unit must in this case be
cleaned by authorized personnel. There is a charge on
this cleaning, even during the warranty time!
7
Power supply: . . . . . . . . . 12 V , 500 mA
Audio output: . . . . . . . . . . 1 V
Dimensions, weight:. . . . . 178 x 88 x 195 mm, 1.5 kg
According to the manufacturer.
Subject to technical modification.
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
sired titles until the entire title sequence (19 titles
max.) has been programmed.
PAUSE" (7): The yellow LED "PLAY" (2) lights up, the
display stops flashing and shows the current title
number. The LED "PROGRAM" continues to flash
while playing.
button "STOP", all LEDs will be extinguished and the
CD player will switch to the stop mode.
drawer is not opened, the title sequence remains
memorized. To replay it again, press the button
"PROG" in the stop mode and start the replay with the
button "PLAY/PAUSE".
"REPEAT" (6) once: The just selected title is contin-
uously repeated. The green LED "REPEAT" (2) lights
up.
vidually programmed title sequence press the button
"REPEAT" a second time. In addition to the LED
"REPEAT" the green LED "ALL" (2) lights up.
"REPEAT" a third time. The two LEDs "REPEAT" and
"ALL" will be extinguished.
Specifications
GB
7