Carrera RC Motion Copter Instrucciones De Montaje Y De Servicio página 6

ENGLISH
moved from the toy. Rechargeable batteries should be removed from the product
before charging. The battery in controller is not replaceable. Supply terminal are
not to be short-circuited. Only use the batteries recommended or equivalent types.
Battery chargers used with the toy are to be regularly examined for damage
to the cord, plug, enclosure and other parts, and in the event of such damage,
they must not be used until the damage has been repaired. The toy is only to
be connected to Class II equipment bearing the following symbol.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This product has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This product generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If the
product does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures :
• Reorient or relocate the receiving antenna.a
• Increase the separation between the product and receiver.
• Connect the product into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC statement
The device contain license-exempt transmitter(s)/ receiver(s) that comply with
Innovation, Science and Economic Development Canada's licence-exempt
RSS(s). Operation is subject to the following two conditions:
1. The device must not cause interference;
2. The device must accept any interference, including interference that may
cause undesired operation of the device.
Guidelines and warnings for the use of LiPo rechargeable batteries
• You have to charge the attached 3.7 V
ble battery in a safe place and at a safe distance to flammable material.
• Never leave the battery unattended while it is charging
• After a flight, the rechargeable battery has to cool down to the ambient air
temperature before charging it.
• You must always use the corresponding LiPo charging unit (USB cable /
remote control). In case of non-compliance with these directions there is a
danger of fire resulting in a health risk and/or damage to property. NEVER
use any other battery charger.
• Should the rechargeable battery swell or deform while discharging or recharg-
ing, you have to immediately stop charging or discharging the battery. Take the
battery out as quickly and carefully as possible and place it in a safe and open
area offside any inflammable material and watch it for at least 15 minutes. In
case you continue charging or discharging a battery which has already started
to swell or deform there is a danger of fire! Even in case of slight deforming or
ballooning the rechargeable battery has to be taken out of operation.
• Store the rechargeable battery at ambient temperature in a dry place.
• Always recharge the battery immediately after use to prevent its becom-
ing deep discharged. Please make sure to allow a pause of about 20 min-
utes between finishing the flight and recharging the battery. Recharge
the battery occasionally (suggested every 2-3 months). Failure to treat
the battery as described above can lead to its becoming defective.
• When transporting or temporarily storing the rechargeable battery the tem-
perature should be between 5-50°C. If possible, do not store the battery or
the model in a car and do not expose it to direct sunlight. In case the battery
is broiled it can be damaged or catch fire.
Note: If the battery voltage/output is low you will recognise that a considera-
ble trim and/or controlling is necessary to avoid that the Quadrocopter starts
trundling. This usually occurs before reaching a battery voltage of 3 V and it
is a good moment to end the flight.
Contents of package
1 x Quadrocopter
1
1 x One-hand controller
1 x USB charging cable
1x Rechargeable Battery
430 mAh /1.591 Wh LiPo rechargea-
Charging the LiPo battery and one-hand controller
Make sure that you charge the LiPo rechargeable battery or one-hand con-
troller supplied only using the LiPo charger (USB cable) supplied. If you try to
charge the rechargeable battery or one-hand controller with another LiPo bat-
tery charger or any other charger, this might cause serious damage. Please
carefully read the previous chapter with warnings and guidelines on the usage
of rechargeable batteries before proceeding. Supply terminals are not to be
short-circuited. You can charge the rechargeable battery or one-hand con-
troller fitted in the quadrocopter with its USB charging cable from a USB port:
Charging via computer:
2a
• Rechargeable batteries are to be removed from the model before
being charged.
• Connect the USB charging cable with the USB port of a computer. The
LED on the USB charger cable lights green indicating that the charger
unit is correctly connected to the computer.If you plug in the quadro-
copter or one-hand controller with a discharged battery, the LED on the
USB charging cable no longer lights up, showing that the quadrocopter
battery or one-hand controller is being charged. The USB charging ca-
ble and the charging socket on the quadrocopter or one-hand controller
are designed to make incorrect connection impossible.
• It takes about 60 minutes to recharge a discharged battery (but NOT a
deep-discharged one). When the battery or one-hand controller is fully
charged, the LED display on the USB charger cable lights up green again.
Note: when supplied, the lipo-battery is already partially charged. So the
first charging cycle may well take less time.
It is essential to follow the connection sequence given above!
Undo the plugged connection on the Quadrocopter when you are not
using the Quadrocopter. Failure to observe this precaution may cause
battery damage!
Insertion of the rechargeable batteries into the Quadrocopter
2b
• Use a screwdriver to open the cover of the battery compartment. Insert
the battery. Close the battery compartment.
• If the LED on the quadrocopter or one-hand controller flashes slowly,
you must change or charge the battery.
Putting on the one-hand controller
Place the rectangular module with the power switch on the flat of your
3
palm so that your thumb fits through the thumb loop. Push your index
finger into the second loop provided. Close the wrist strap on your palm.
Frequency bind between model and remote control
The Carrera RC Quadrocopter and the one-hand controller automatically
4
link up renewed with every operational start-up. If initially there are any
problems with communication between the Carrera RC Quadrocopter and the
one-hand controller, please carry out a new frequency bind.
• Connect the battery in the model.
• Press the ON/OFF button on the top.
• The LEDs on the quadrocopter now flash rhythmically.
• Switch on the one-hand controller at the power switch.
• WARNING! Immediately after switching it on, place the Quadrocopter
on a flat and level surface. The gyro-system will then set itself automat-
ically. Also ensure that the quadrocopter is aligned correctly and its
front (red rotor blades) points away from you.
• The binding has now been successfully established.
• The LEDs on the one-hand controller or quadrocopter now light up permanently.
Description of the Quadrocopter
1. Rotor system
5
2. Rotor protection cage
3. LEDs
4. Battery cable
6
5. Quadrocopter connecting plug
6. Battery compartment
7. Anti-collision sensors
NOTE: The function of the anti-collision sensors can be disrupted by
light and direct sunshine. The sensors are unable to identify window
panes as an obstacle.
Range of functions of the remote control
1. Power ON / OFF (OFF = hold for 10 sec.)
7
2. Index finger loop with button
3. Thumb loop
6