Mixing Container Assembly; Preparation; Operating The Mixer; Refill Ingredients - Profi Cook PC-KM 1063 Instrucciones De Servicio

Mixing Container Assembly

For this, please also refer to figures 6 and 7 on page 6.
NOTE:
On fig. 6: The mixer jug has a mark at the bottom. The symbols
can be found on the motor part.
1. Align the mixer jug marking with the
2. Turn the mixer jug a short distance clockwise. It latches into place.

Preparation

1. Cut all ingredients in small pieces.
2. Fill the ingredients into the mixing container. Observe the maximum
capacity.
3. Fit the lid onto the blender jug.
4. Close the lid with the stopper (17).

Operating the mixer

Any speed can be selected with the control knob.
WARNING:
• Always disconnect the mains plug before you remove the accessories and clean the appliance!
• Do not immerse the motor part in water for cleaning in any case. This may lead to electric shock or fire.
• Some parts of the accessories are very sharp. There is risk of injury!
CAUTION:
• Do not use a wire brush or other abrasive utensils for cleaning.
• Do not use aggressive or abrasive cleaning agents.

Motor Housing

• Clean the housing only with a damp cloth and a squirt of washing-up
liquid. Dry with a cloth.

Accessories of the kitchen appliance

WARNING: Risk of injury!
Some parts of the accessory are very sharp!
CAUTION:
• The attachments are not suitable for dishwasher. Heat and aggressive
cleaning agents may warp or discolour the attachments.
• Do not rinse the whisk attachment in a bowl of hot water or under
running water. If water penetrates inside the attachment, it cannot be
removed.
• You may clean all other components that have come in contact with food
in a bowl of hot water.
• Rinse with clean water and dry thoroughly.
• The two whisks can simply be pulled off from the attachment. Fit them
back into the attachment after cleaning and drying. Check that the whisk
is secure.

Blender Accessories

Pre-Cleaning
Fill the mixing container half with water and run the appliance for approx.
10 seconds. Dispose of the liquid.
General cleaning
• Remove the mixing container for thorough cleaning.
WARNING: Risk of injury!
Knife and knife assembly are sharp.
42
and
symbol.

Cleaning

If the jug is very full or the liquid foams, select a lower speed.

Refill Ingredients

1. Switch the appliance off. Wait until the blade comes to a stop.
2. Fill in ingredients or spices through the stopper opening.
3. Close lid and stopper opening again.
4. Continue operation.

Stop Operation

1. Switch the appliance off. Wait until the blade comes to a stop.
2. Disconnect from mains power supply.
3. Turn the blender jug anticlockwise from the motor housing.
4. Remove the lid before pouring out the contents.
5. Clean all used parts as described under "Cleaning".
IMPORTANT NOTE:
Do not store citrus juices or acidic foodstuffs in metal containers.
• You can clean the blender jug and the lid with cap in a bowl of hot water.
Afterwards, rinse with clean water and dry the parts off.

Storage

• Clean the appliance as instructed. Ensue that all accessories are com-
pletely dry.
• We recommend that you keep the appliance in the original packaging if it
will not be used for long periods.
• Always store the appliance out of the reach of children in a dry, well
ventilated place.

Troubleshooting

The appliance does not function
Possible cause:
The appliance has no power supply.
Remedy:
• Check the socket with another appliance.
• Plug in the mains plug correctly.
• Check the main circuit breaker.
Possible cause:
The appliance is faulty.
Remedy:
• Contact our service center or a specialist.
Further possible causes:
Your appliance is equipped with safety switches.
They prevent accidental motor start.
Remedy:
• Check correct position of
- the working bowl
- the lid of the working bowl or
- the filter sieve or
- the blender jug.