Know Your Product; Operation - Normfest WSK2000W Instrucciones De Uso

excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
of kickback or wheel breakage.
b) Do not position your body in line with and be-
hind the rotating wheel. When the wheel, at the
point of operation, is moving away from your body,
the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never at-
tempt to remove the cut-off wheel from the cut
while the wheel is in motion otherwise kick-
back may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
d) Do not restart work directly on the work piece
again. Allow the disc to reach maximum speed
and contact the work piece carefully. The disc
may hang, abruptly lift, or move backwards if the
unit is restarted under load.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
f) Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The pro-
truding wheel may cut gas or water pipes, electrical
wiring or objects that can cause kickback.
Safety Warnings Specific for Sanding Opera-
tions:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturer's recommenda-
tions, when selecting sanding paper. Larger
sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snag-
ging, tearing of the disc or kickback.
Safety Warnings Specific for Wire Brushing
Operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load
and centrifugal forces.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Spindle
2.1. Grinding wheel (Use only with a wheel guard for
grinding wheel!)*
Original instructions
2.2. Cutting wheel (Use only with a wheel guard for
cutting wheel!)*
3.1. Wheel guard for grinding wheel
3.2. Wheel guard for cutting wheel*
4. Support flange
5. Fixing flange
6. Auxiliary handle
7. ON/OFF switch
8. ON/OFF switch locking button
9. Spindle lock button
ACCESSORIES TO BE USED WITH THIS
POWER TOOL
10. Wire cup brush*
11. Plastic (rubber) backing pad*
12. Sandpaper*
13. Lock nut*
* The additional accessories shown in the illustrations or
described in the text are not included in the delivery.

Operation

These power tools are supplied from singlephase alter-
nating current mains only. They are double insulated ac-
cording to EN 60745, IEC 60745-1 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive.
This power tool is designed for cutting, grinding and
brushing mainly metals without using water.
PRIOR TO INITIAL OPERATION
▪ The machine may be delivered with the wheel guard
mounted at the factory. Ensure that the wheel guard is
mounted properly and fixed reliably prior to the initial
and any following operation.
▪ The machine may be delivered with the wheel mount-
ed at the factory. Ensure that the wheel is mounted
properly and fixed reliably prior to the initial and any
following operation.
▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
▪ Always check the position of ON/OFF switch. The
power tool must be connected and disconnected to
the power supply socket only when this switch is in
OFF position. If the plug is connected to a receptacle
while the power switch is in the ON position, the pow-
er tool will start operating immediately, which could
cause a serious accident.
▪ Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance.
▪ When using diamond cutting discs, pay attention that
the direction-of-rotation arrow on the diamond cut-
17
EN