Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
All fasteners are in the parts bag. Do not discard
any parts or material until the unit is assembled.
WARNING: Before doing any as-
sembly or maintenance to the
mower, remove the wire from the
spark plug.
NOTE: In this instruction book, left and right
describe the location of a part with the oper-
ator on the seat.
NOTE: Illustrations and pictorials begin on
page 2.
NOTE: To assemble the following loose
parts, use the fasteners shown at full size in
Figure 17.
How To Attach The Bagger Mount
1. (Figure 1) If equipped, remove and discard
the two screws from the rear of the frame.
Use these two holes to attach the bagger
mount (1).
2. Attach the bottom of the bagger mount (1)
to the frame with the bolt (2) and nut (3). Do
not tighten at this time.
3. Attach the back of the bagger mount (1) to
the frame with bolts (4), washers (5), and
nuts (6). Make sure the fasteners are tight.
NOTE: For easier assembly, use a ratchet
and socket to tighten the bolts.
4. Tighten bolt (2) and nut (3).
5. (Figure 2) Mount the channel (7) in the
bagger mount (1).
IMPORTANT: If you remove the grass
bagger to mount a different pull-behind
attachment, do not remove the bagger
mount (1). Use the hitch pin hole in the
bagger mount to attach a different attach-
ment. If the bagger mount (1) is removed,
make sure to install the fasteners in the
holes in the rear of the frame.
6. (Figure 3) Install the channel pin (9) fully
into the right side of the channel (7). Rotate
the channel pin (9) counterclockwise to lock
the channel (7) in place.
7. Mount the outer tube (10) to the channel (7)
with bolts (12), washers (13), and nuts 14.
8. (Figure 4) Mount the center tube 15 to the
channel (7) with bolts (12), washers (13),
and nuts 14. Make sure the fasteners are
tight.
9. Attach the caps 16 to the ends of the tubes.
How To Mount The Cover
1. (Figure 5) Assemble the hinge (1) to the
cover (2) with bolt (3) and nut (4). Push the
hinge (1) toward the top of the cover (2).
Tighten the fasteners.
2. Attach the handle (5) to the cover (2) with
bolt (6) and nut (7). Tighten the fasteners.
3. Set the cover (2) in the operating position on
top of the outer tube. Fasten the hinge (1) to
the channel (10) with pin (11) and hair pin
(12).
F-050900L
How To Mount The Extension Tube
1. (Figure 7) Attach latch pin (2) to the exten-
sion tube (1) with bolt (3) and nut (4).
2. Move the lift lever to the highest cut position.
3. Disconnect the wire from the spark plug.
Raise the deflector (5). Rotate the blade
away from the discharge opening.
The blade has sharp edges. Always
be careful of the position of the
blade.
4. (Figure 8) Slide the extension tube (1)
under the deflector bracket (6). Mount the
extension tube (1) to the top of the mower
housing with bolt (7) and nut (8).
5. Attach the extension tube (1) to the side of
the mower housing with bolt (7) and nut (8).
Make sure the fasteners are tight.
6. Connect the wire to the spark plug.
How To Mount The Connector Tube
1. (Figure 9) Assemble the handle (2) and the
rubber latch (3) to the connector tube (1).
Hold screws (4) and (5) with a short screw-
driver and tighten locknuts (6) and (7).
2. Slide the connector tube (1) into the elbow
(8). Align the hole (9) in the connector tube
(1) with the hole (9) in the elbow (8).
3. Fasten the elbow (8) to the connector tube
(1) with screw (10). Tighten screw (10) until
the head of the screw touches the elbow (8).
4. Move the lift lever to the lowest position.
5. (Figure 10) Hold the handle (2) on the con-
nector tube (1). Slide the end of the elbow
(8) through the hole in the cover (11).
6. (Figure 11) Align the rubber latch (3) with
the latch pin (12).
7. Slide the connector tube (1) over the exten-
sion tube (13).
8. Lock the rubber latch (3) to the latch pin
(12).
NOTE: To help the elbow (8) slide when you
open or close the cover (11), put wax or pol-
ish on the elbow (8).
How To Assemble The Containers
NOTE: The containers can only be as-
sembled one way. Carefully read and follow
the instructions below.
1. (Figure 12) Separate the six container sec-
tions into two groups. Each group will have a
top section (10), a middle section (9), and
a bottom section (8).
2. Look for a number on the side of each top
section (10). The numbers for the two top
sections are 1 and 3. Set the two top sec-
tions (10) on the ground with the flanges (7)
on top.
3. Look for the numbers on the side of each
middle section (9). One middle section (9)
has the numbers 1 - 2. The other middle
section (9) has the numbers 3 and 4.
4. Set middle section numbered 1 - 2 inside of
top section numbered 1.
8
5. Set middle section numbered 3 - 4 inside of
top section numbered 3.
6. Look for a number on the side of each bot-
tom section (8). The numbers for the two
bottom sections are 2 and 4.
7. Set bottom section numbered 2 inside of
middle section numbered 1 - 2.
8. Set bottom section numbered 4 inside of
middle section numbered 3 - 4.
9. (Figure 13) Stand with one foot inside the
three sections. Lift the top section (10) until
all three sections connect together. Make
sure all four corners of each section are
locked together.
10. (Figure 14) Fasten the top section (10) and
the middle section (9) of each container to-
gether with four fasteners (7). From the in-
side of each container, push the fasteners
through the holes.
How To Mount The Containers
(Figure 15)
1. Tilt the seat forward. Raise the cover (1).
2. Plastic bag linings are optional accessories
that can be used for easy removal of the
grass.
3. If desired, put the optional plastic bag linings
in the containers (2).
4. Slide the containers (2) onto the support
tubes (3). Make sure the CAUTION (4), on
the side of the containers (2), is to the rear.
5. Lower the cover (1). Pull back on the handle
(5) and push the cover (1) down until the
cover (1) locks in place.
IMPORTANT: For the grass bagger to work
correctly, the cover (1) must be locked in the
down position.
Container Linings
1. For easy removal of the grass, use plastic
bag linings inside the containers. Use one of
the following sizes.
S 33 gallons
S 4 bushels
S 145 liters
OPERATION
NOTE: Illustrations and pictorials begin on
page 2.
WARNING: Do not ride up or down
slopes that are too steep to back
straight up. Never ride the unit
across a slope. See the "Slope Guide" in
the back of this book for information on
how to check slopes.
How To Use The Grass Bagger
To operate with the grass bagger, follow the
steps below.
IMPORTANT: Do not cut wet grass. Wet grass
will not discharge correctly into the grass
bagger.
GB
Publicidad
