PIAGGIO 1D001230 Instrucciones De Uso página 13

ACKNOWLEDGEMENT OF SIREN IN ALARM STATUS:
If you wish to acknowledge the siren without disengaging the system during an alarm cycle, you can do so
ACKNOWLEDGEMENT OF SIREN IN ALARM STATUS:
by pressing key B of the remote control while the siren is buzzing. This will immediately interrupt the sound
If you wish to acknowledge the siren without disengaging the system during an alarm cycle, you can do so
signal, restoring the system in alert status.
ACKNOWLEDGEMENT OF SIREN IN ALARM STATUS:
by pressing key B of the remote control while the siren is buzzing. This will immediately interrupt the sound
If you wish to acknowledge the siren without disengaging the system during an alarm cycle, you can do so
signal, restoring the system in alert status.
DISABLING WITHOUT ALARM MEMORY:
ACKNOWLEDGEMENT OF SIREN IN ALARM STATUS:
by pressing key B of the remote control while the siren is buzzing. This will immediately interrupt the sound
By pressing key A of the remote control or inputting the electronic key in the specific housing in alert or alarm
If you wish to acknowledge the siren without disengaging the system during an alarm cycle, you can do so
signal, restoring the system in alert status.
DISABLING WITHOUT ALARM MEMORY:
status, the system will disengage, notifying the event by flashing the turn signals twice, emitting two sound
by pressing key B of the remote control while the siren is buzzing. This will immediately interrupt the sound
By pressing key A of the remote control or inputting the electronic key in the specific housing in alert or alarm
signals and turning off the LED. From this moment, it is possible to start-up the vehicle's motor.
signal, restoring the system in alert status.
DISABLING WITHOUT ALARM MEMORY:
status, the system will disengage, notifying the event by flashing the turn signals twice, emitting two sound
By pressing key A of the remote control or inputting the electronic key in the specific housing in alert or alarm
signals and turning off the LED. From this moment, it is possible to start-up the vehicle's motor.
DISABLING WITH ALARM MEMORY:
DISABLING WITHOUT ALARM MEMORY:
status, the system will disengage, notifying the event by flashing the turn signals twice, emitting two sound
Should alarms be triggered during the alert status, these will be notified during the disabling phase by
By pressing key A of the remote control or inputting the electronic key in the specific housing in alert or alarm
signals and turning off the LED. From this moment, it is possible to start-up the vehicle's motor.
DISABLING WITH ALARM MEMORY:
flashing the turn signals four times and by emitting four sound signals. Afterwards, the user can analyse in
status, the system will disengage, notifying the event by flashing the turn signals twice, emitting two sound
Should alarms be triggered during the alert status, these will be notified during the disabling phase by
detail the sensor that triggered the alarm by pressing key C of the remote control. The sensor's indication will
signals and turning off the LED. From this moment, it is possible to start-up the vehicle's motor.
DISABLING WITH ALARM MEMORY:
flashing the turn signals four times and by emitting four sound signals. Afterwards, the user can analyse in
take place as follows:
Should alarms be triggered during the alert status, these will be notified during the disabling phase by
detail the sensor that triggered the alarm by pressing key C of the remote control. The sensor's indication will
DISABLING WITH ALARM MEMORY:
flashing the turn signals four times and by emitting four sound signals. Afterwards, the user can analyse in
take place as follows:
CAUSE OF ALARM
Should alarms be triggered during the alert status, these will be notified during the disabling phase by
detail the sensor that triggered the alarm by pressing key C of the remote control. The sensor's indication will
flashing the turn signals four times and by emitting four sound signals. Afterwards, the user can analyse in
take place as follows:
THE TURN SIGNALS WILL FLASH FOUR TIMES AND FOUR SOUND SIGNALS WILL BE EMITTED WITH ALARM DISABLING. BY
CAUSE OF ALARM
detail the sensor that triggered the alarm by pressing key C of the remote control. The sensor's indication will
PRESSING KEY "C" OF THE REMOTE CONTROL, THE FOLLOWING SIGNALS WILL BE GENERATED:
take place as follows:
Panel activation
THE TURN SIGNALS WILL FLASH FOUR TIMES AND FOUR SOUND SIGNALS WILL BE EMITTED WITH ALARM DISABLING. BY
CAUSE OF ALARM
Instantaneous input (if programmed)
PRESSING KEY "C" OF THE REMOTE CONTROL, THE FOLLOWING SIGNALS WILL BE GENERATED:
Lifting sensor
Panel activation
THE TURN SIGNALS WILL FLASH FOUR TIMES AND FOUR SOUND SIGNALS WILL BE EMITTED WITH ALARM DISABLING. BY
CAUSE OF ALARM
Self-powering (if foreseen)
Instantaneous input (if programmed)
PRESSING KEY "C" OF THE REMOTE CONTROL, THE FOLLOWING SIGNALS WILL BE GENERATED:
Lifting sensor
Panel activation
THE TURN SIGNALS WILL FLASH FOUR TIMES AND FOUR SOUND SIGNALS WILL BE EMITTED WITH ALARM DISABLING. BY
Self-powering (if foreseen)
INTENTIONAL ACTIVATION OF THE SIREN (PANIC ALARM): Instantaneous input (if programmed)
PRESSING KEY "C" OF THE REMOTE CONTROL, THE FOLLOWING SIGNALS WILL BE GENERATED:
Lifting sensor
Panel activation
If desired, the user can intentionally activate the system's siren by simply pressing key B of the remote
Self-powering (if foreseen)
Instantaneous input (if programmed) INTENTIONAL ACTIVATION OF THE SIREN (PANIC ALARM):
control. The operation will be possible only with the system disengaged or in alert status.
Lifting sensor
If desired, the user can intentionally activate the system's siren by simply pressing key B of the remote
Self-powering (if foreseen)
INTENTIONAL ACTIVATION OF THE SIREN (PANIC ALARM):
control. The operation will be possible only with the system disengaged or in alert status.
If desired, the user can intentionally activate the system's siren by simply pressing key B of the remote
INTENTIONAL ACTIVATION OF THE SIREN (PANIC ALARM):
control. The operation will be possible only with the system disengaged or in alert status.
If desired, the user can intentionally activate the system's siren by simply pressing key B of the remote
control. The operation will be possible only with the system disengaged or in alert status.
SIGNAL EMITTED
SIGNAL EMITTED
One flashing
SIGNAL EMITTED
Two flashing
Four flashing
One flashing
SIGNAL EMITTED
Six flashing
Two flashing
Four flashing
One flashing
Six flashing
Two flashing
Four flashing
One flashing
Six flashing
Two flashing
Four flashing
Six flashing
INTERFACE USED
INTERFACE USED
Led
INTERFACE USED
Led
Led
Led
INTERFACE USED
Led
Led
Led
Led
Led
Led
Led
Led
Led
Led
Led
Led