Before Starting The Equipment - EINHELL TC-MS 3017 T Manual De Instrucciones Original

in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
The machine has to be set up in a stable po-
sition, i.e. it has to be bolted to a workbench,
a universal stand or the like.
•
All the covers and safety devices have to be
properly fitted before the machine is switched
on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
Anl_TC_MS_3017_T_SPK7.indb 24 Anl_TC_MS_3017_T_SPK7.indb 24
GB
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
is the same as that for your mains.
•
Secure the clamp (37) on the top of the stop
rail using the screw.
5.1 Setting up the saw (Fig. 1-4)
•
Insert the two workpiece support clips (20) in
the mounts (13) provided on the side of the
tool and fasten them in place with screws.
•
To prevent the saw from toppling backwards,
the additional foot (a) must be pulled out of
the equipment (Fig. 4).
5.2 Converting the combination saw (Fig. 1-8)
The saw has two working positions:
A: Bench circular saw (Fig. 1)
B: Crosscut and miter saw (Fig. 2)
Convert the combination saw can be conver-
ted exactly as described below, otherwise the
components may be damaged.
Important: Pull out the mains plug before you
convert the saw.
When it is supplied, the saw will be in mode A
(bench circular saw)
5.2.1 Converting the saw for crosscut mode
(Fig. 5, 6)
•
Tighten the locking screw (10) and the tighte-
ning screw (22).
•
Undo the locking screws (15, 24) and lift the
saw table so that it moves into the highest po-
sition. Tighten the two locking screws again.
•
Press the saw table (16) down at the front and
draw the safety pin (23) out at the same time.
•
Caution! The return spring automatically lifts
the machine. Do not let go of the saw table,
but move it slowly up to the swung-out positi-
on by applying counterpressure.
•
When you draw out the safety pin (23), this
deactivates the switch (4) for bench mode
and activates the switch for crosscut mode
(3).
•
Remove the bottom saw blade cover (14).
•
The saw has now been set to crosscut mode.
5.2.2 Converting the saw for bench mode
(Fig. 5-7)
- 24 -
21.12.2016 17:37:42 21.12.2016 17:37:42