Electrical Requirements & Information - PROFLO PFS5838 Manual De Instalación Y Funcionamiento

ELEcTRIcAL REqUIREMENTS AND INfORMATION
1. Whirlpool units require dedicated 20 Amp,120V service.
2. You must provide a receptacle with a 20-amp configuration.
3. See local codes for proper wire size. If not specified, use #12 Copper only wire.
The unit must be connected to a circuit interrupter (GFCI) provided by the installer. The (GFCI) breaker should be tested on a routine basis.
To test the (GFCI) breaker, push the test button. The GFCI should interrupt power. To restore power, push the RESET button. If the GFCI fails
to operate in this manner there is ground current flowing, indicating the possibility of an electrical shock. Do not use the unit. Disconnect the
unit and have the problem corrected by a qualified service representative before using.
WARNING
WARNING
PROFLO.COM
WHIRLPOOL CIRCUIT WITH OPTIONAL HEATER
POWER SPEED WAVE
BACK OF 3 BUTTON CONTROL
CONTROLL VALVE
TMS-P/TIMER
CONTROL
ON / OFF PUMP
9 AMP
RISK OF ELECTRICAL SHOCK. All pumps and blowers must be connected
to a ground fault circuit interrupter (GFCI) protected outlets. Standard Line
OPTIONAL
Total Massage units can be operated on a single service. All heaters must be
HEATER
connected to a ground fault circuit interrupter (GFCI) protected outlets, separate
120V / 20AMP
from the pump and/or blower.
MALE PLUG
120V, 60 HZ
20 AMP GFCI
Electrical outlet must be mounted 4" (101mm) above the floor line and 12"
max (305mm) inside from the edge of the bathtub, or in accordance with local
AIR MASSAGE CIRCUIT
building and electrical codes.
• Risks of component over heat. Do not use electric extension cord to power
the unit. Operating the pump without enough water in bathtub can cause
permanent damage to the pump/motor.
POWER SPEED WAVE
• If CFGI unit indicates a malfunction, per manufacturer's instructions, turn OFF
BACK OF 3 BUTTON CONTROL
power and do not attempt to use the bathtub until the source of the problem
has been identified and corrected.
PIGGY BLOWER
9.25 AMP
ELECTRICAL
FEED
120V, 60 HZ
20 AMP GFCI
GFCI GFCI
BRADENTON & PROVINCETOWN WHIRLPOOL
WITH INSTALLED AIR SWITCH
AIR SWITCH
120V, 60 HZ
20 AMP GFCI
ELECTRICAL
FEED
GFCI GFCI
PUMP FLOW
0.5 AMP
ELECTRICAL
FEED
120V, 60 HZ
20 AMP GFCI
GFCI GFCI
TMS - VARIABLE
CONTROL
PROFLO WHIRLPOOL
WITH INSTALLED AIR SWITCH
PUMP / MOTOR
TOTAL MASSAGE CIRCUIT WITH OPTIONAL HEATER
AIR SPEED WAVE JETS SPEED WAVE
BACK OF 6 BTN CONTROL
PUMP FLOW
CONTROLL VALVE
TMS-P/TIMER
0.5 AMP
CONTROL
ON / OFF PUMP
9 AMP
OPTIONAL
HEATER
120V / 20AMP
MALE PLUG
120V, 60 HZ
20 AMP GFCI
BRADENTON & PROVINCETOWN TOTAL MASSAGE
CIRCUIT WITH OPTIONAL HEATER
AIR SWITCH
ON / OFF PUMP
9 AMP
HEATER
ELECTRICAL
FEED
120V, 60 HZ
9.25 AMP
GFCI
BRADENTON & PROVINCETOWN
AIR BATH CIRCUIT
AIR SWITCH
PIGGY BLOWER
9.5 AMP
ELECTRICAL
FEED
GFCI GFCI
TMS - VARIABLE
CONTROL
PIGGY BLOWER
9.5 AMP
ELECTRICAL
FEED
120V, 60 HZ
20 AMP GFCI
GFCI GFCI
AIR SWITCH
CONTROL BOX
PIGGY BLOWER
9.5 AMP
120V, 60 HZ
20 AMP GFCI
GFCI
CONTROL BOX
120V, 60 HZ
20 AMP GFCI
5