Before Starting The Equipment - EINHELL GE-CM 36/36 Li Manual De Instrucciones

circumstances this fi eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before starting the equipment

The lawn mower is delivered unassembled. The
complete push bar, the rear wheels and the grass
basket must be assembled before using the lawn
mower. Follow the operating instructions step-
by-step and use the pictures provided as a visual
guide to easily assemble the equipment.
Fitting the wheels (Figures 3a, b and 4)
Take the rear wheels (Item11) and mount them
on the axle as shown in Figure 3a. Then slide the
washer (Item 23) onto the axle and fasten all parts
with the supplied split pin (Item 22) as shown in
Figure 3b. Finally, press the wheel caps (Item 10)
onto the wheels (Figure 4).
Mounting the push bar (Fig. 5 to 9)
First take the spring (Item 16) and the handlebar
mount (Item 12) and mount them on the relevant
axle (Figure 5). Depending on the version, these
parts may already be fi tted along with the nut with
the quick clamping function. In this case, remove
the nut with quick clamping function to continue
with assembly. Now insert the push bar holder
(Item 3) into the handlebar mount (Item 12) and
secure with the quick clamping function (Item 17)
(Figure 6).
The top push bar (Item 2) must be pushed onto
the push bar holders (Item 3) and secured as
shown above in Figure 7. Then attach the power
cable to the push bar (Fig. 8) using the cable clips
(Item 18). Now you can select the push bar height
in three steps from 93.5 to 115.5 cm (Figure 9/
Item A).
Notice!
The handle height may only be adjusted within
the marked range.
If necessary, turn the respective quick-release
fastener back suffi ciently on the thread so that the
quick-release lever (Fig. 9/Item B) can then be
fl ipped towards the back.
•
Press in the long handle and secure in the
desired position using the quick clamping
function (Figure 9)
Anl_GE_CM_36-36_Li_SPK9.indb 24 Anl_GE_CM_36-36_Li_SPK9.indb 24
GB
Warning!
Always set the identical handle height on both
sides.
•
Use the cable clips to align the cable in ac-
cordance with the long handle (Figure 8)
Mounting the grass basket
(see Figs. 10 to 12)
First, plug the left (Item 21) and right (Item 20)
part of the housing together as shown in Figure
10. Then plug the top part of the housing (Item 19)
onto the already mounted parts (Figure 11). Be-
fore you fi t the grass basket you must ensure that
the motor is switched off and the blade is not ro-
tating. Lift the ejector fl ap (Item 6) with one hand.
With the other hand, hold the grass basket by the
handle and hook it in from above (Fig. 12).
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling level
indicator (Fig. 2/Item 24) which is opened by the
air current that the lawn mower generates during
operation. If the fl ap closes during mowing, the
grass collecting device is full and must be emp-
tied. To ensure the proper functioning of the fi lling
level indicator, the holes under the fl ap must be
kept clean and open.
Adjusting the cutting height
Warning!
Adjust the cutting height only when the motor is
switched off and the safety plug has been remo-
ved.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.
The cutting height is adjusted as follows
(see Fig. 13):
1. Push the lever (1) outwards.
2. Set the lever (2) to the desired cutting height.
3. Release the lever (1) and check that it is se-
curely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-75 mm
in 6 intervals, and can be read off on the scale
(Fig. 14/D).
- 24 -
21.10.2019 06:30:58 21.10.2019 06:30:58