Festool KS 60 E Manual De Instrucciones página 29

The rotary knob [1-5] locks the saw unit so that
it can no longer be moved forwards or back­
wards.
The spotlight SL-KS60 (available as
an accessory depending on the mod­
el) casts a shadow over the saw blade
and onto the workpiece. Use the
On/Off switch [2-3] to activate this
function. The cutting line becomes
visible when the saw unit is lowered.
Slide-sawing
When slide-sawing, the saw blade is guided to
the workpiece from the front, which means the
sawing is controlled and requires less effort.
Recommended for workpieces over 70 mm in
width.
Correct sawing process when slide-sawing
Avoid reverse cutting. When sawing, do
not pull the lowered saw unit up to the
body. The saw blade could hook in and the saw
unit could accelerate towards the operator.
► Release the rotary knob for the slide locking
device [1-5].
► Pull the saw unit to the limit stop.
► Press and hold the safety button [1-2].
► Push the saw unit down and, when doing so,
press and hold the On/Off switch [1-3].
► Only guide the saw unit towards the work­
piece once the set speed has been reached.
► Cut the workpiece; slide the saw unit
through the workpiece until the limit stop.
► Once the cut is complete, guide the saw unit
back to its upwards position.
The pendulum guard closes automatically.
► Release the safety button and the On/Off
switch. Close the rotary knob.
8.4 Saw the mitre angle [10]
Standard mitre angle
The following mitre angles (left and right) auto­
matically engage: 0°, 15°, 22.5°, 30°, 45°, 60°
Setting the standard mitre angle
► Release the rotary knob
► Press the detent lever but do not hook it in­
to place .
► Rotate the rotary base into the required po­
sition ; release the detent lever shortly
before the required angle has been
reached.
The rotary base easily clicks into place at
the intended mitre angles.
► Close the rotary knob
.
.
Setting individual mitre angles
► Release the rotary knob
► Press the detent lever
to place by pressing on it at the left.
► Continuously swivel the rotary base into the
required position
► Close the rotary knob
8.5 Saw the mitre angle [10]
Standard mitre angle
The following mitre angles (left and right) auto­
matically engage: 0°, 15°, 22.5°, 30°, 45°, 60°
Setting the standard mitre angle
► Release the rotary knob
► Press the detent lever but do not hook it in­
to place .
► Rotate the rotary base into the required po­
sition ; release the detent lever shortly
before the required angle has been
reached.
The rotary base easily clicks into place at
the intended mitre angles.
► Close the rotary knob
Setting individual mitre angles
► Release the rotary knob
► Press the detent lever
to place by pressing on it at the left.
► Continuously swivel the rotary base into the
required position
► Close the rotary knob
8.6 Saw inclined cuts [11]
Moving or removing the stop rulers
may make it necessary to implement special
settings for inclined cutting, see section
Inclination to the left between 0° and 45°
► Loosen the star handle
► Tilt the saw unit to the desired cutting angle
.
► Tighten the star handle
Inclination to the right between 0° and 45°:
► Loosen the star handle
► Press the release button
relieve the tension by slightly tilting it in the
opposite direction.
► Tilt the saw unit to the desired cutting angle
.
► Tighten the star handle
English
.
and let it click in­
.
.
.
.
.
and let it click in­
.
.
7.3 .
.
.
.
; if required,
.
29