General Operation - AEG TT 4471 USB Instrucciones De Servicio

Ocultar thumbs

página de 38

/ 38
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

English

connectors (Cinch)

14 PHONO / LINE switch

15 USB (Type B) port

16 DC IN 15 V

connector

17 ON / STANDBY switch

18 Dust cover

19 Dust cover hinges (2 x)

Not Shown

1 x Turntable mat

1 x Adaptor for 45 rpm records (puck)

1 x Protective cap for record needle

1x Spare record needle

1x Audio cable (2 x RCA)

1x USB cable

Start-up of the Device / Introduction

• Select a suitable location for the device, such as a dry,

flat, non-slip surface on which it is easy to operate the

machine.

• Ensure that the device is sufficiently ventilated!

• Place the device where it is not exposed to direct sunlight.

• Do not place anything on top of the device.

• Please check whether you need to install the drive belt

on the motor pully. To do that, please turn the turntable

until the recess is aligned with the motor. You will be able

to see the brass-coloured drive roller then. Carefully pull

the drive belt away from the turntable a bit and centre it

above the drive roller of the motor.

• Put the turntable mat onto the turntable before you put

a record on.

• Please install the protective cap for the record needle if

you do not use the device.

• Sensitive surfaces may be protected by plastic foil.

Remove this foil.

Connect the Device to a Stereo System

There are two different ways to connect the device to your

stereo system. You can use a cinch cable (2 x RCA) to connect

the device.

a) If your amplifier has a PHONO input, connect the device

to this input. Please create a ground connection between

the ground jack (12) and your amplifier. (The ground cable

is not included in the scope of delivery).

WARNING: Important!

Please pay attention that the switch (14) on the back of

the device is in the PHONO position! Otherwise, the

playback might be very loud and might damage your

Hi-Fi equipment. We do not assume any liability for

possible consequential damages.

b) If your amplifier does not have a PHONO input anymore,

please connect the device to the AUX IN jacks of your

amplifier.

TT4471USB_IM_new

In order to enable playback via the integrated amplifier,

the switch (14) must be in the LINE position.

NOTE:

Please ensure that the plug-in connectors are firmly in

place. Poor connections can result in interference.

Power Supply

1. Ensure that the voltage is the same as that indicated on

the model identification plate.

2. Insert the grid plug into a properly installed three prong

socket. Connect the device with the plug connector by

inserting its plug into the DC 15 V

device.

CAUTION:

• Only use the supplied power adaptor for this device.

Do not use for other devices.

• Only use power adaptor with 15 V (

adaptors may cause damage to the device.

NOTE:

If the unit is not used for a long period of time, unplug the

mains plug from the socket.

Transportation Safety Lock (Locking Screw)

To protect the turntable from damages in transport, the

locking screw (1) was turned upwards.

• Before you can use the turntable, you have to completely

move down the screw in clockwise direction with a

screwdriver.

• Before you transport the turntable, please turn the screw

up again.

Installation of the Dust Cover

Please refer to the figure on page 3.

1. Install the hinges in the mounting brackets on the back of

the device.

2. Install the dust cover on the upper end of the hinges.

Do you want to take the dust cover off again?

1. Flip the dust cover open.

2. Carefully remove the dust cover, together with the hinges,

in an upward direction away from the device.

3. Now remove the hinges from the dust cover.