Publicidad
Idiomas disponibles
Idiomas disponibles
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2
Safety instructions for reciprocating saws
▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the operator an electric shock.
▶ Use clamps or another practical way to secure and support the workpiece to a stable platform.
Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
2.3
Additional safety instructions for saws
Personal safety
▶ Keep your hands away from the cutting area and the blade.
▶ Do not reach underneath the workpiece.
▶ Position yourself off to one side of the blade, never bring the blade into line with your body. The saw can
jump backward toward you if kickback occurs.
▶ Never use the power tool without a fully functional hand guard.
▶ If the saw blade binds or when you interrupt work for any reason, switch off the saw and hold it motionless
in the material until the saw blade comes to a complete stop. Never attempt to remove the saw from the
workpiece or pull the saw back while the blade is in motion, as otherwise the saw could kick back.
▶ When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are
not in engagement with the workpiece.
▶ Use extra caution when sawing into walls or other blind areas. As it enters the material the blade might
encounter a hidden obstruction, resulting in kickback.
▶ Always use a saw blade of appropriate length. The saw blade must project beyond the workpiece
throughout the entire stroke.
▶ Do not use dull or damaged blades. These cause increased friction and present a high risk of the saw
blade binding or kicking back.
▶ Secure the workpiece in a sturdy holder. Never hold the workpiece with your hand or across your leg.
▶ Apply only moderate pressure and cut at an appropriate speed, especially when cutting large-diameter
pipes. This will help to prevent the power tool overheating.
▶ Before cutting through pipes, make sure that they are empty of medium. Drain the pipes if necessary.
▶ When cutting through pipes, hold the power tool above the level of the pipe you are cutting through.
▶ The power tool is not protected against ingress of moisture. Liquid running out of a pipe can cause a
short circuit in the power tool.
4
English
2208240
*2208240*
Publicidad
