Maintenance - RIDGID R82008 Manual Del Operador

Taladro de 10 mm (3/8 pulg.)12 v de iones
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION
wARNING:
Be prepared for binding at bit breakthrough. When
these situations occur, drill has a tendency to grab
and kick opposite to the direction of rotation and
could cause loss of control when breaking through
material. If not prepared, this loss of control can
result in possible serious injury.
 When drilling hard, smooth surfaces, use a center punch
to mark the desired hole location. This will prevent the
drill bit from slipping off-center as the hole is started.
 When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
 If the bit jams in the workpiece or if the drill stalls, stop
the tool immediately. Remove the bit from the workpiece
and determine the reason for jamming.
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the brake
is functioning properly, sparks will be visible through the
vent slots on the housing. This is normal and is the action
of the brake.

MAINTENANCE

wARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
wARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
wARNING:
To avoid serious personal injury, always remove
the battery pack from the tool when cleaning or
performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 11
AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
WOOD DRILLING
For maximum performance, use high speed steel bits for
wood drilling.
 Begin drilling at a very low speed to prevent the bit from
slipping off the starting point. Increase the speed as the
drill bit bites into the material.
 When drilling through holes, place a block of wood behind
the workpiece to prevent ragged or splintered edges on
the back side of the hole.
METAL DRILLING
For maximum performance, use high speed steel bits for
metal or steel drilling.
 Begin drilling at a very low speed to prevent the bit from
slipping off the starting point.
 Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much pressure
will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits; and
• Produce off-center or irregular-shaped holes.
 When drilling large holes in metal, start with a small bit,
then finish with a larger bit. Also, lubricate the bit with oil
to improve drilling action and increase bit life.
wARNING:
Do not at any time let brake fluids, gasoline,
®
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
bATTERY PACk REMOVAL AND PREPARATION
FOR RECYCLING
wARNING:
Upon removal, cover the battery pack's terminals
with heavy-duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove any
of its components. Lithium-ion batteries must be
recycled or disposed of properly. Also, never touch
both terminals with metal objects and/or body
parts as short circuit may result. Keep away from
children. Failure to comply with these warnings
could result in fire and/or serious injury.
9 - English

Publicidad

Tabla de contenido
loading

Tabla de contenido