Publicidad
Idiomas disponibles
Idiomas disponibles
Installation
INSTALLATION
CAUTION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
LGE Wall Sleeve.
If you decide to keep the existing wall sleeve,
you have to redirect the louvers at the back of
the wall sleeve illustration.
The use of pliers is
recommended.
If you DO NOT redirect, you
run the risk of poor performance
or product
failure. This is not covered under the terms of
the LGE warranty.
* Pick a location
which will allow the conditioned
air
to blow into the area you want. Good installation
with special attention to the proper position
of the
unit will lessen the chance that service will be
needed.
ITEMS
IN INSTALLATION
HARDWARE
You may not need all parts in the kit. Discard unused
)arts
ITEM (inches)
Plastic grille
Vertical insulation strip
Around
Insulation
Strips
Horizontal
Insulation
Strip
Support
Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
Grille Rear
263/4 x 161/2
159/16x 13/8x 13/8
671/8
x
13/8
x
25/32
5927/32
x
13/8x 13j_
237/32x 1318 x 13/lc
13/4
X
13/8
X
45/16
14 x 41/2 x
1/8
1113/16X 1 X3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
1
HOW TO INSTALL
D
dentify the existing wall sleeve before installing
the unit from the listed below.
Brand
White-Westinghouse
Frigidaire
Carrier (52F series)
General
Electric
/Hotpoint
Wall Sleeve Dimensions (inches)
Width
Height
25-1/2
15-1/4
26
15-5/8
Whirlpool
25-7/8
16-1/2
Fedders/Emerson
27
16-3/4
LGE
25-7/8
15-17/32
Emerson/Fedders
26-3/4
15-3/4
Carrier (51S Series)
25-3/4
16-7/8
Friedrich
27
16-3/4
Depth
16, 17-1/2
or 22
16-7/8
17-1/8
or 23
16-3/4
or 19-3/4
16-23/32
15
18-5/8
16-3/4
All wall sleeves used to mount the new Air
Conditioner
must be in sound structural
condition
and have a rear grille that securely
attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner.
H
El
El
Remove old air conditioner
from existing wall
sleeve.
Clean the interior of an existing sleeve.
(Do not disturb seals.)
Wall sleeve must be securely fastened
in wall
before installing the air conditioner.
Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
Prepare the wall sleeve for installation
of the
unit. If you plan to use your existing wall sleeve,
and it is not LGE, use procedure
B or C below.
Procedure
A
B
C
Brand
LGE
White-Westinghouse
Frigidaire
Carrier
(52F series)
General
Electric
/Hotpoint
Whirlpool
Carrier (51S series)
Fedders/Emerson
Emerson/Fedders
Friedrich
Depth(inches)
16-23/32
16, 17-1/2
or 22
16-7/8
17-1/8 or 23
18-5/8
16-3/4
or 19-3/4
15
16-3/4
_
Install new unit into wall sleeve.
CAUTION
When installation
is completed,
replacement
unit
MUST have a rearward
slope as shown. To
achieve
1/4" slope, remove the backing from the
11-13/16"
shim strips and attach them as shown
below in Fig. 3. Place the higher portion of shim to
the front of the rib on base of wall sleeve.
1" high]'[--
SHIM
PLACEMENT
lI 3/4" High
UNIT
Walt Sleeve
UNIT INSTALLATION
FIG. 3
12
Room Air Conditioner
Publicidad
