How To Install - LG LT1030HR Manual Del Propietário

Installation
iNSTALLATiON
_, CAUTION
We strongly recommend the removal of the
old waft sleeve and the installation of a new
LGE Wall Sleeve,
If you decide to keep the existing wall sleeve,
you have to redirect the louvers at the back of
the wall sleeve illustration. The use of pliers is
recommended. If you DO NOT redirect, you run
the risk of poor performance or product failure.
This is not covered under the terms of the LGE
warranty.
• Pick a location which will allow the conditioned air
to blow into the area you want. Good installation
with special attention to the proper position of the
unit will lessen the chance that service will be
needed.
ITEMS |N INSTALLATION HARDWARE
You may not need all parts in the kit. Discard
unused parts
iTEM (inches)
Plastic grille
Horizontal Insulation Strips
Around Insulation Strips
Support Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
Gdlle Rear
268/4 X 161/2
13/8 X 5/8 X 273/16
13/8 X 13/8 X 273/16
13/8 X 3/4, X 611/2
13/8 X 13/8 X 611/2
13/4 X 13/8 X 45/16
14 X 41/2 X 1/8
13xl X3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
1
HOW TO iNSTALL
D Identify the existing wall sleeve before
installing the unit from the listed below.
Wall Sleeve Dimensions (inches',
Brand
Width Height Depth
White-Westinghouse
Frigidaire 25-1/2 15-1/4 16, 17-1/2
or 22
Carrier (52F series)
General Electric
/Hotpoint 26 15-5/8 16-7/8
Whirlpool 25-7/8 16-1/2 17-1/8
or 23
Fedders/Emerson 27 16-3/4 16-3/4
or 19-3/4
LGE 25-7/8 15-17/32 t6-23/32
Emerson/Fedders 26-3/4 15-3/4 15
Carrier (51S Series) 25-3/4 16-7/8 18-5/8
Friedrich 27 16-3/4 16-3/4
All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner,
Remove old air conditioner from existing wall
sleeve.
Clean the interior of an existing sleeve.
(Do not disturb seals.)
D all sleeve must be securely fastened in wall
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
D repare the wall sleeve for installation of the
unit. If you plan to use your existing wall
sleeve, and it is not LGE, use procedure B or
C below.
Procedure Brand Depth(inches)
A LG E 16-23/32
White-Westinghouse 16, 17-1/2
Frigidaire Carder
or 22
(52F series)
B General Electric
16-7/8
/Hotpoint
Whirlpool 17-1/8 or 23
Carder (51S series) 18-5/8
16-3/4
Fedders/Emerson
or 19-3/4
C
Emerson/Fedders 15
Friedrich 16-3/4
Q Install new unit into wall sleeve.
_, CAUTION
When installation is completed, replacement unit
MUST have a rearward slope as shown. To achieve
1/4" slope, remove the backing from the 11-13/16"
shim strips and attach them as shown below in Fig.
3. Place the higher portion of shim to the front of
the rib on base of wall sleeve.
UNIT Wall Sleeve
SHIM PLACEMENT UNIT INSTALLATION
FIG. 3
12 Room Air Conditioner