Technical Data; Safety Instructions; Mains Connection - AEG SB2E 705 R Instrucciones De Uso

TECHNICAL DATA

Nominal power output ................................................................
Rated output ...............................................................................
No-load speed, 1st gear .............................................................
No-load speed, 2nd gear ............................................................
Speed under load max., 1st gear ...............................................
Speed under load max., 2nd gear ..............................................
Rate of percussion under load max. ...........................................
Static jamming moment*, 1st gear/2nd gear ..............................
Drilling capacity in concrete, 1st gear/2nd gear .........................
Drilling capacity in brick and tile, 1st gear/2nd gear ...................
Drilling capacity in steel, 1st gear/2nd gear ................................
Drilling capacity in soft- wood, with Forstner bit in 1st gear .......
Drilling capacity in soft- wood, with auger bit in 1st gear ............
Drilling capacity in hard-wood with Forstner bit in 1st gear ........
Drilling capacity in hard-wood, with auger bit in 1st gear ...........
Max. Spax's bit size in soft-wood ...............................................
Max. Spax's bit size in hard-wood ..............................................
Drill opening range .....................................................................
Drive shank ................................................................................
Chuck neck diameter ..................................................................
Weight without cable ..................................................................
Typical weighted acceleration in the hand-arm area ..................
Typical A-weighted sound levels:
Sound pressure level ...............................................................
Sound power level ...................................................................
Wear ear protectors! Measured values determined according to EN 50 144.
The data stated above apply for models with 230 - 240 V. In case of deviating mains voltage, the data stated on the rating plate
are applicable.
* Measured according to AEG norm N 877318

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the attached
leaflet!
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Always use the auxiliary handle, even if the machine has a
safety clutch since this safety clutch only engages when the
machine blocks with a jerk.
When working with large drill diameters, the auxiliary handle
must be fastened in a right angle with the main handle (see
illustrations, section „Twisting the handle").
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The electronic drill/screwdriver can be universally used for
drilling, percussion drilling, screwdriving and cutting screw
threads.
Do not use this product in any other way as stated for normal
use.

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the
design conforms to safety class II.
21 ENGLISH
SB2E 750 RX SB2E 715 R
SB2E 750 R
SuperTorque
......... 750 W ...............715 W .............. 705 W ................ 750 W
......... 375 W ...............360 W .............. 355 W ................ 375 W
.... 0-1200 min ........ 0-1200 min
-1
.... 0-3400 min ........ 0-3400 min
-1
......... 750 min ............. 770 min
-1
....... 2100 min ........... 2200 min
-1
....... 31500 min ......... 33000 min
-1
........ 62/30 Nm ............ 60/29 Nm ............50/25 Nm ..............62/30 Nm
...... 20/10 mm .........20/10 mm ........ 20/10 mm .......... 20/10 mm
...... 22/12 mm .........22/12 mm ........ 22/12 mm .......... 22/12 mm
........ 13/8 mm ...........13/8 mm .......... 13/8 mm ............ 13/8 mm
........... 35 mm ..............35 mm ............. 35 mm ............... 35 mm
........... 16 mm ..............16 mm ............. 16 mm ............... 16 mm
........... 30 mm ..............30 mm ............. 30 mm ............... 30 mm
........... 12 mm ..............12 mm ............. 12 mm ............... 12 mm
....... 6x90 mm .......... 6x90 mm ......... 6x90 mm ........... 6x90 mm
....... 5x60 mm .......... 5x60 mm ......... 5x60 mm ........... 5x60 mm
..... 1,5-13 mm ........1,5-13 mm ....... 1,5-13 mm ......... 1,5-13 mm
... 1/2"x20 ............1/2"x20 ........... 1/2"x20 ............. 1/2"x20
........... 43 mm ..............43 mm ............. 43 mm ............... 43 mm
.......... 2,5 kg ...............2,5 kg ............... 2,5 kg ................ 2,5 kg
........... 15 m/s .............15 m/s
2
......... 101 dB (A) ........101 dB (A) ....... 101 dB (A) ......... 101 dB (A)
..........114 dB (A) ........ 114 dB (A) ........114 dB (A) ..........114 dB (A)
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3, in accordance with the regulations 98/37/
EC, 89/336/EEC
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust
hold the machine with the chuck facing down vertically, and
completely open and close the chuck. The collected dust will
fall from the chuck. It is recommended to regularly use
cleaner for the clamping jaws and the clamping jaw borings.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge, Postfach
320, D-71361 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
SB2E 705 R SB2-750
SuperTorque
....... 0-1200 min .............1200 min
-1 -1
....... 0-3400 min .............3400 min
-1 -1
.............770 min ...............750 min
-1 -1
...........2200 min .............2100 min
-1 -1
.........33000 min ...........31500 min
-1 -1
............. 15 m/s .............. 15 m/s
2 2
Rainer Warnicki
Manager Product Marketing
and Development
-1
-1
-1
-1
-1
2