Kickback And Related Warnings; Additional Safety Warnings - Carat DustCatch 125 Laser Instrucciones De Manejo

n) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
o) Regularly clean the power tool's air vents. The motor's fan will
draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
p) Do not operate the power tool near flammable materials. Sparks
could ignite these materials.
q) Do not use accessories that require liquid coolants. Using water
or other liquid coolants may result in electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or away
from the operator, depending on direction of the wheel's movement
at the point of pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by taking
proper precautions as given below.
a) Maintain a firm grip on the power tool and position your body
and arm to allow you to resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over kickback or torque
reaction during start‐up. The operator can control torque reactions
or kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory. The accessory
may kickback over your hand.
c) Do not position your body in the area where the power tool will
move if kickback occurs. Kickback will propel the tool in the direction
opposite to the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp edges, etc. Avoid
bouncing and snagging the accessory. Corners, sharp edges or
bouncing have a tendency to snag the rotating accessory and cause
loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw
blade. Such blades create frequent kickback and loss of control over
the power tool.
f) Do not "jam" the cut‐off wheel or apply excessive pressure. Do
not attempt to make an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility to twisting or binding
of the wheel in the cut and the possibility of kickback or wheel
breakage.
g) When wheel is binding or when interrupting a cut for any reason,
switch off the power tool and hold the power tool motionless until
the wheel comes to a complete stop. Never attempt to remove the
cut‐off wheel from the cut while the wheel is in motion, otherwise
kickback may occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
h) Do not restart the cutting operation in the workpiece. Let the
wheel reach full speed and carefully reenter the cut. The wheel may
bind, walk up or kickback if the power tool is restarted in the
workpiece.
i) Support panels or any oversized workpiece to minimize the risk of
wheel pinching and kickback. Large workpieces tend to sag under
their own weight. Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on both sides of
the wheel.
j) Use extra caution when making a "pocket cut" into existing walls
or other blind areas. The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause kickback.
ADDITIONAL SAFETY WARNINGS
a) Use suitable detectors to determine if utility lines are hidden in
the work area or call the local utility company for assistance.
ENGLISCH – ORIGINAL INSTRUCTIONS |
Contact with electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Penetrating a water line
causes property damage or may cause an electric shock.
b) When working stone, use dust extraction. The vacuum cleaner
must be approved for the extraction of stone dust. Using this
equipment reduces dust‐related hazards.
c) When working with the machine, always hold it firmly with both
hands and provide for a secure stance. The power tool is guided
more secure with both hands.
d) Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
e) Never use the machine with a damaged cable. Do not touch the
damaged cable and pull the mains plug when the cable is damaged
while working. Damaged cables increase the risk of an electric shock.
7. GUARANTEE
The guarantee period for the DustCatch 125 Laser and DustCatch 230
Laser is 12 months, starting at the moment of delivery. Guarantee
claims have to be proved by showing the invoice of purchase. The
guarantee contains repairing the occurred lacks; which can be leaded
back to material and/or manufacturing failures.
Not covered by the guarantee:
 Lacks or damages, which occurred by misuse or incorrect
connecting.
 Power tool overload.
 By bad or wrong maintenance.
 When the given instructions aren't followed correctly.
 The power tool is used by unauthorized persons.
 The power tool is used for unsuitable purposes.
 The power tool is repaired with non‐original spare parts.
 The machine code is affected or removed.
 Lacks by fire, moist and/or transport damage.
Carat Centrale B.V.
Nikkelstraat 18
4523 AB Breda
The Netherlands
T: +31 (0) 765 420 814
F: +31 (0) 765 440 490
E: info@carat‐centrale.com
15