Urrea 6205 Manual De Usuario Y Garantía página 44

1. Tighten clutch pressure wheel to 10% of
torque wrench rated capacity.
2. From the main screen, press and hold the EN-
TER key for three seconds. The User
choices menu will be displayed.
3. Scroll to the CONFIGURE menu selection by
pressing the UP key two times:
4. Press the Enter key to display the Configure
menu and scroll to the CALIBRATION
menu selection by pressing the Down key:
5. Press the Enter key to display the Password
Entry screen:
6. Enter the password: 91748 by pressing the
Up or Down keys to increment/decrement the
highlighted digit, followed by the Enter key af-
ter each digit is set.
7. Following the entry of the last password
digit, the Calibration menu will be displayed.
8. Highlight the CAL ANGLE menu selection by
pressing the Down key:
9. Press the Enter
key and the prepare
tor angle calibration
screen will be dis-
played:
10. Set the angle test fixture stops for 180 de-
gree rotation.
11. Place the wrench in the angle test fixture.
12. Press the Enter key
and verify the "TURN"
prompt is displayed:
13. Release the index
stop on the fixture
and rotate the wrench
180 degrees in 6 sec.
14. Press the Enter key and verify the "CAL
COMPLETE" prompt is displayed:
15. Press the Enter key to return to the Calibra-
tion menu.
16. Use the Down
key to highlight the
CHECK ANGLE menu
selection:
17. Press the Enter
key to display the cal
check screen:
18. Rotate the wrench 45 degrees in the clock-
wise direction and while maintaining torque
on the wrench, verify the wrench reads within
42.5° to 47.5°.
19. Rotate the wrench another 45 degrees in
the clockwise direction (90° total) and while
maintaining torque on the wrench, verify the
wrench reads within 87.1° to 92.9°.
E N G L I S H •
20. Rotate the wrench another 45 degrees in
the clockwise direction (135° total) and while
maintaining torque on the wrench, verify the
wrench reads within 131.6° to 138.3°.
21. Rotate the wrench another 45 degrees in
the clockwise direction (180° total) and verify
the wrench reads within 176.2° to 138.3°.
22. Release the torque on the wrench.
23. Rotate the wrench 45 degrees in the coun-
ter-clockwise direction and while maintaining
torque on the wrench, verify the wrench reads
within -42.5° to -47.5°.
24. Rotate the wrench another 45 degrees in
the counter-clockwise direction (90° total) and
while maintaining torque on the wrench, veri-
fy the wrench reads within -87.1° to -92.9°.
25. Rotate the wrench another 45 degrees in
the counter-clockwise direction (135° total)
and while maintaining torque on the wrench,
verify the wrench reads within -131.6° to
-138.3°.
26. Rotate the wrench another 45 degrees in
the counter-clockwise direction (180° total)
and verify the wrench reads within -176.2° to
-138.3°.
27. Release the torque on the wrench.
MAINTENANCE
Contact your URREA sales representative for
calibration or repair services. Clean the wrench
by wiping with a damp cloth. DO NOT use sol-
vents, thinners or carburetor cleaners. DO NOT
immerse in anything. Service, repair and cali-
bration are to be done by the URREA Service
Center only. Contact your URREA Tools repre-
sentative. Ratchet head repair can be done by
URREA Representative or user.
CERTIFICATION
This torque-angle wrench was calibrated at the
factory using angular displacement and torque
measurement instruments that are traceable to
the National Institute of Standards and Technol-
ogy (N.I.S.T.). Torque parameters comply with ISO
6789-2003 and ASME B107.300-2010.
NOTE: No U.S. or International Standards exist
for angle wrenches.
NOTES
- DO NOT use the torque wrench when pow-
ered off.
- If the display shows "ZERO TARE ERROR" at
power on with no torque applied, the wrench
is damaged and must be returned for repair.
- The wrench must be held still during angle
mode reset. Motion is indicated by alternating
segments of the display "- -".
- Remove battery when stored for extended
periods.
U se r's m a n ua l
8