DeWalt D25404 Manual De Instrucciones página 2

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V .....................volts
Hz ...................hertz
min .................minutes
or DC .....direct current
...................Class I Construction
.......................(grounded)
...................Class II Construction
(double insulated)
.../min ............per minute
IPM .................impacts per minute
SPM ...............strokes per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. D
not operate, check power supply.
COMPONENTS (Fig. 1, 2)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
A. Side handle
B. Trigger switch
Side Handle (Fig. 1)
CAUTION: Always use side handle (A) and hold rotary hammer with both hands.. It clamps
to the front of the gear case as shown and can be rotated 360˚ to permit right or left hand use.
The grip may be unscrewed and retightened to relocate the handle in the desired location.
Switch (Fig. 1)
The variable speed trigger switch (B) permits speed control. The farther the trigger switch is
de pressed, the higher the speed of the rotary hammer.
NOTE: Use lower speeds for starting holes without a center punch, drilling in metal, plastics or
ceramics, or driving screws. Higher speeds are better for drilling in wood and composition board
and for using abrasive and polishing accessories.
Mode Selector (Fig. 2)
CAUTION: Never change the mode while the unit is running.
For straight drilling, rotate the mode selector (C) until the arrow points to the drill bit symbol. For
rotary hammer, align the arrow with the hammer symbol. For chipping mode align arrow with
the chipping symbol.
NOTE: The mode selector (C) must be in drill, hammer or chipping mode at all times. There are
no operable positions in between.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Depth Rod
To adjust the depth rod (D), loosen the wing nut (E) and move rod so that the distance between
the end of the rod and the end of the bit equals the desired drilling depth. Tighten the wing nut.
When drilling with depth rod, stop when end of rod reaches surface of material.
Quick Change SDS Chuck (Fig. 3)
The SDS chuck can be easily removed by turning the collar (F) into the unlocked position (G) to
release the chuck.
The SDS chuck can be easily attached by inserting the chuck into the spindle of the tool and
turning the collar to the locked position (H). The chuck will click when properly installed.
Drilling
1. Always unplug the drill when attaching or changing bits or accessories.
2. Always use sharp drill bits. For WOOD, use twist drill bits, spade bits, power auger bits, or
hole saws. For METAL, use steel twist drill bits or hole saws. For MASONRY, such as brick,
cement, cinder block, etc., use carbide-tipped bits rated for percussion drilling.
3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a
wood "back-up" block to prevent damage to the material.
4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting,
but do not push hard enough to stall the motor or deflect the bit.
5. Hold tool firmly to control the twisting action of the drill.
6. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE
TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO
NOT CLICK TRIGGER ON AND OFF IN AN AT TEMPT TO START A STALLED DRILL —
THIS CAN DAMAGE THE DRILL.
7. To minimize stalling or breaking through the material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent
jamming.
9. With variable speed drills there is no need to center punch the point to be drilled. Use a slow
speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep
enough to drill without the bit skipping out.
DRILLING IN METAL
Start drilling with slow speed and increase to full power while applying firm pressure on the tool.
A smooth even flow of metal chips indicates the proper drilling rate. Use a cutting lubricant when
drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil or lard oil; bacon-grease will also serve the
purpose.
NOTE: Large [5/16" to 1/2" (7,6 mm to 13 mm)] holes in steel can be made easier if a pilot hole
[5/32" to 3/16" (3,8 mm to 5 mm] is drilled first.
DRILLING IN WOOD
Start drilling with slow speed and increase to full power while applying firm pressure on the tool.
Holes in wood can be made with the same twist drills used for metal. These bits may overheat
unless pulled out frequently to clear chips from the flutes. For larger holes, use spade bits, power
auger bits, or hole saws. Work that is apt to splinter should be backed up with a block of wood.
DRILLING IN MASONRY
When drilling in masonry, use carbide tipped bits rated for percussion drilling and be certain that
the bit is sharp. Use a constant and firm force on the tool to drill most effectively. A smooth, even
flow of dust indicates the proper drilling rate.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
A .........................amperes
W ........................watts
or AC .............alternating current
or AC/DC......alternating or direct current
n o .......................no load speed
n .........................rated speed
.......................earthing terminal
........................safety alert symbol
BPM ...................beats per minute
RPM ...................revolutions per minute
sfpm ...................surface feet per minute
WALT tools are factory tested; if this tool does
E
C. Hammer/Drill selector
D. Depth rod
FIG. 1 E
A
FIG. 2
C
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only D WALT recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
E
(1-800-433-9258) or visit our website: www.dewalt.com.
MAXIMUM RECOMMENDED CAPACITIES
Maximum Capacity
R.P.M.
BITS, Metal Drilling
Wood, Flat Boring
Optimum Capacity
No-load BPM
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by a D
a D WALT authorized service center or other qualified service personnel. Always use identical
E
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D WALT (1-800-433-9258). This warranty does not apply to
E
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D WALT (1-800-433-9258) for a free replacement.
E
D
B
FIG. 3
F
G
H
WALT, have not been tested
E
1-1/8" (30 mm) Concrete
0–730 (No Load)
1/2" (13 mm)
1-1/8" (30 mm)
1/2" - 1" (13 to 25 mm) Concrete
0-4,100
WALT factory service center,
E
WALT Power Tool, Laser, or
E
WALT
E