Specific Safety Rules - Makita PC5000C Manual De Instrucciones

ENGLISH
1. Lock lever
2. Switch trigger
3. Indication lamp
4. Base (for PC5001C only)
5. Hex wrench
6. Front roller
7. Hex socket head bolt
8. Stock removal amount
9. Base
SPECIFICATIONS
Model
Wheel diameter
Hole diameter
Spindle thread
Rated speed (n) / No load speed (
Overall length
Net weight
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing concrete surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to
Concrete Planer safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
Safety Warnings for Grinding Operation:
1. This power tool is intended to function as a
grinder with offset diamond wheels. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as grinding with abrasive wheels,
sanding, wire brushing, polishing or cutting-off
are not recommended to be performed with this
power tool. Operations for which the power tool was
not designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
Explanation of general view
10. Same level
11. Square or ruler
12. Raise
13. Lower
14. Dust cover
15. Screw
16. Lock nut
17. Lock nut wrench
18. Diamond wheel
PC5000C
n
)
o
437 mm
ENE002-1
ENF002-1
GEB043-3
19. Shaft lock
20. Dust bag
21. Dust cover cap
22. The whole roller holder
23. Hex bolt
24. Limit mark
25. Brush holder cap
26. Screwdriver
125 mm
22.23 mm
M14
10,000 (min
4.0 kg
/II
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. The arbour size of wheels, flanges or any other
accessory must properly fit the spindle of the
power tool. Accessories with arbour holes that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as offset diamond
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-
load speed for one minute. Damaged accessories
will normally break apart during this test time.
8. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
PC5001C
-1
)
479 mm
5.1 kg
5