Festool CS 70 VL Instrucciones De Montaje página 6

Compact CS 70 Accessories
Symbols
Warning of general danger
Read the Operating Instructions/Notes!
 For the alignment and adjustment of all indi-
vidual components, we recommend using a
spirit level or an aluminium ruler (min. 1 m long)
1 Extension table CS 70 VB [1-1]
The extension table CS 70 VB can be fi tted to the
base table to enable exact cuts with a stop up to a
cutting width of 680 mm.
The saw table is widened by 405 mm if an extension
table is fi tted on a long side of the table (usually
the right).
Proceed as follows (Fig. 2):
• Unfold supports [2-5] at a 90° angle to the table
top.
• Turn rotary knobs [2-8] fully to the left.
• Place the outer edge of the extension table on
the edge of the base table in a slightly raised
position (Fig. 2).
• Lower extension table so that the peripheral
clamping edge [2-4] lies between the profi le edge
[2-7] and clamping plate [2-7].
• Insert the end of the front support [2-2] into
the slot [2-1] in the table frame, push down and
tighten with knurled nut [2-3].
• Suspend rear support in slot. Push extension
table down and tighten rear knurled nut.
• Adjust exact height. Place guide stop on base
table up to saw blade.
• Adjust height of extension table to same height
as base table with screwdriver at the adjusting
screws [4-1].
• Attention! Do not align with outer edge of table
since this may be 0.2-0.3 mm below the rest of
the table.
• Fit angle fence [1-3] centrally over joint between
base table and extension table so that when the
fence is clamped the extension table is aligned
with the edge of the base table.
• Tighten front rotary knob [2-8].
• Push extension table down on joint at rear and
tighten rear rotary knob.
• Then remove the angle fence.
• Screw in adjusting screws [2-10] fully with screw-
driver. If the extension table is removed and then
re-mounted it must be pushed back against this
stop (adjusting screw).
• This fi xation means that it no longer has to be
aligned with the angle fence.
• Check that the extension table is exactly level with
the base table using the guide stop.
• The fl atness of the base table can be adjusted by
adjusting the fastening [2-6].
To enable the angle fence and ripping-cut fence
to be adjusted according to the existing scale, the
scale of the extension table must be fi tted directly
onto the base table's scale (Fig. 4).
Proceed as follows:
• Release the fastening bolts [4-2] for the exten-
sion table's scale.
• Slide the scale to the correct setting.
• Re-tighten fastening bolts.
2 Extension table CS 70 VL [1-2]
The extension table CS 70 VL can be mounted on
the rear of the CS 70 EB to provide a safe support
when sawing longer work pieces.
The saw table is thus extended by 530 mm.
Proceed as follows (Fig. 3):
• Mount left and right fi tting angle [3-6] to rear
of frame with enclosed bolts, square nuts and
washers. Tighten the bolts [3-10].
• If a CS 70 ST sliding table is already fi tted the
fi tting angle for the extension table is placed on
the fi tting angle for the sliding table on the side of
the sliding table and both fi tting angles fastened
together (on top of one another).
• The enclosed 4 mm washer then has to be in-
serted beneath the fi tting angle on the other side.
• Unfold supports [3-4] at a 90° angle to the tab-
letop.
• Release left and right rotary knobs [3-8] by ap-
prox. 3-4 rotations (turn anti-clockwise).
• Suspend the extension table by the threaded bolts
of the rotary knobs [3-8] in the slots [3-9] on the
fi tting angle in a slightly raised position.
• The fi tting angle hereby lies between the rotary
knob [3-8] and bow [3-7].
• Lower the extension table onto roughly the same
level as the saw table and insert the end of the
support [3-2] into the slot [3-1] in the table
frame, press down and fasten with knurled nut
[3-3].
6