Settings - Festool CTH 26 E/a Manual De Instrucciones Original

Sistemas móviles de aspiración
Ocultar thumbs Ver también para CTH 26 E/a:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 32
WARNING
Risk of injury from tools starting up unex­
pectedly
► Before setting the switch to the "AUTO" or
"MAN" position, make sure that the con­
nected tool is switched off.
The switch [1-11] serves as an on/off switch.
Switch position "0"
Appliance socket [1-4] is disconnected from the
power, mobile dust extractor is switched off.
"MAN" switch position
Appliance socket [1-4] is connected to the pow­
er, the mobile dust extractor starts.
"Auto" switch position
Appliance socket [1-4] is connected to the pow­
er, the mobile dust extractor starts when the
connected tool is switched on.
7

Settings

7.1
Adjusting the hose diameter
► Adjust the hose diameter adjuster [1-9] to
match the diameter of the connected hose.
The monitoring devices will measure
the air speed in the extractor hose
correctly as a result (see chap­
ter Volumetric flow monitoring).
7.2
Connecting electric power tools
WARNING
Risk of injury
► Observe the maximum appliance socket
connected load (see chapter "Technical da­
ta")
► Switch off the electric power tool.
► Connect the electric power tool to the appli­
ance socket [1-5].
7.3
Connecting pneumatic tools
WARNING
Risk of injury
► Switch off the air tool.
If the compressed air module [1-3] (496141) is
installed, the automatic switch-on function of
the mobile dust extractor also works in combi­
nation with pneumatic tools.
We also recommend installing the VE service
unit (495886). The service unit filters and lubri­
cates the compressed air and enables an ad­
justment of the air pressure. An IAS adapter
(454757) is available to connect Festool pneu­
matic tools to the IAS system.
The operating pressure of the tool must be
6 bar for the automatic switch-on unit to func­
tion correctly.
7.4
Adjusting the suction power
► Use the rotary knob .
7.5
Applying the brake
Folding out the black brake lever [1-15] pre­
vents the mobile dust extractor from rolling. To
achieve this, lift the front end of the mobile dust
extractor slightly and push the black brake lev­
er downwards until it latches into place. Push
the green lever again to release.
7.6
Temperature cut-out
A temperature cut-out switches the mobile dust
extractor off when it reaches a critical tempera­
ture to prevent overheating.
► A temperature cut-out switches the mobile
dust extractor off when it reaches a critical
temperature to prevent overheating.
► Switch off the mobile dust extractor, allow
to cool for about 5 minutes then switch on
again.
Not possible to switch on: contact
Festool service workshop.
7.7
Changing the filter bag (SC-FIS-
CT26/48)
Removing the filter bag [4]
► Open the locking clips [2-2] and remove the
top section of the machine[2-1].
► Remove the filter bag.
► Dispose of the used filter bag in accordance
with statutory regulations.
► Clean the dust container [2-3].
Inserting the filter bag [5]
► Insert a new filter bag (SC-FIS-CT26/48) in
the inlet port of the dust container and in­
terlock it. Important: be aware that the
locking engages.
Make sure that the filter bag is not
pinched between the top and bottom
sections.
► Replace the top section [2-1] and close the
locking clips [2-2].
English
17

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cth 48 e/a202403202404202405202403, 202404

Tabla de contenido