Remote Programming; Dialer Parameters Management - Tyco BTEL-3G Manual De Usuario

f
Pressing the key for 3 seconds from any menu level allows you to return to standby status. This feature is valid only when
exploring the menus or during programming, even if a voice message from the menu is playing. To return to the menu, you will
need to retype the User PIN.
I I I I I If you use this command during programming, any data entered will be disregarded.
Access the User Menu key by entering the following formula:
where <User PIN> is a 5-digit number (the factory default user PIN is 00000).
Access to programming is indicated by the RED LED
f f f f f
I I I I I Keeping the
key pressed for 3 seconds does not cancel entry of the User PIN. If you become aware
that the PIN that you are typing is invalid, you need to wait a few seconds for the operation to be
cancelled automatically, or press the
I I I I I If you enter the User PIN during a call to access the User Menu (yellow LED lit), the key inputs will not
be confirmed by a tone but the code will still be accepted and you will access the menu at the end of
the call. You cannot enter the User PIN at the beginning or end of a call (yellow LED switching).

Remote programming

The user can perform some operations remotely with a PSTN or GSM phone (in this case, it needs to be a touch-tone
telephone). Again, voice instructions are provided to assist with programming. For remote operations, access the remote
control menu in one of the following ways:
1) During a voice call from the BTEL-3G; press the
#
the call. When the key is recognized, the BTEL-3G will sound a double tone (beep-boop) confirming this; at this
point, type in the <User PIN>.
I I I I I If access to voice menu is not possible, set the voice message repetition to 3 or more (ask to the
installer).
I I I I I With somee telephone types could be necessary to keep the key
2) By making a call to the BTEL-3G from a telephone number stored in the phone book. After recognizing the telephone
number, the BTEL-3G accepts the call and sounds a double tone (beep-boop) as confirmation; at this point, type in
the <User PIN>.
The <User PIN> is a 5-digit number (the factory default user PIN is 00000).
If no key is pressed within 10 seconds the call is ended. If the <User PIN> you typed in is correct, the BTEL-3G plays
the voice message "CODE ACCEPTED" and after a 2-second pause it begins to play the voice menu; if the PIN is
incorrect, the device will play the voice message "INCORRECT CODE" followed by a single tone (boop). The
maximum number of tries allowed to enter the <User PIN> is 3, after which the BTEL-3G will end the call and resume
its normal operations (for example, delivering a voice message to another number). If the <User PIN> typed is valid, the
User Menu will open, from which you can perform the following operations: Output Management, Monitor Input,
Environment Listen Management, Block Calls, and Change Code.
I I I I I You must wait that the voice menu ends before you can do your choice!

Dialer Parameters Management

This section is used to manage the main features needed for the BTEL-3G to function.
Output Management
Once you enter this section,the voice instructions start to list the programming for each output.To enter this programming mode,type
the following keypad sequence:
0
to enable the output or to disable;to exit, press
Monitor Input
To check the active/inactive status of the four inputs (L1, L2, L3, and L4), type the following keypad sequence:
10
e e e e e
key to finish the entry and then try again.
( (
( ( (
#
key when the message is over and before the BTEL-3G ends
1 1
,a voice message will inform the user of the status of the first output (O1).Press the
9
.The operation is repeated for outputs O2 and O3.
c e
<User PIN>
turning on (see the section "Status LEDs").
# # # # #
pressed for at least 1 second.
Ë Ë Ë Ë Ë
( ( ( ( (
1 2
1
key
BTEL-3G