Tabla de contenido
Publicidad
GB
MOUNTING INSTRUCTIONS
1 // This magnetic glass board is suitable for mounting and use in interiors at room temperature and with a standard level of humidity (40-60 %).
2 // Do not mount the LED glass board on damp walls or electrically conductive surfaces. Before mounting, check that there are no service pipes, e.g. for
electricity, gas or water, in that part of the wall. In addition to this, there should be an electrical socket close to the magnetic glass board.
3 // When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as stone or tiles. We
cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted and do not remove the protective
corners until it is attached to the wall.
4 // The board should only be mounted on walls that are even, hard, and heat-resistant.
5 // Two people are required to mount the 130 x 55 cm magnetic glass boards.
6 // In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling template(s). You will find the measurements for the
relevant distances between drill holes on page 10 and on our website at www.sigel.co.uk/mounting
MOUNTING
1 // The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling template(s) make(s) it simple to mark the position of the
drill holes. The wall fixings d are screwed securely to the wall using anchors b and screws c. The side of the board with the Sigel logo should be facing
outwards (Fig. I).
Tip: Please use a spirit level to check that the wall fixings d are lined up straight.
The wall fixings d have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall fixings d vertically
or horizontally as required. Then tighten the screw again.
2 // The magnetic glass board a is then mounted onto the wall fixings d (Fig. II). There are two or four mounting fittings on the back of the board for this.
Each mounting fitting e has two openings (Fig. III); the wall fixings d must always be slotted into the top opening rather than the side opening, whether the
board is hung in portrait or landscape format. Place the mounting fittings e on the back of the board over the wall fixings d so that the wall fixings d are in
the centre (Fig. III). Now slide the board downwards so that the wall fixings d click into the mounting fittings e (Fig. IV) and the board is mounted securely.
Make sure that the magnetic glass board is always mounted on two or four fittings and check that the board is securely in place before letting go. Silicon pads
on the back of the board keep it steady while it is being written on.
3 // Insert the European plug f or UK plug g into the socket and turn on the switch. The LED strip h at the back of the board will now light up.
SAFETY PRECAUTIONS
The light source cannot be replaced. When the LED has reached the end of its service life (approx. 25,000 hours), please replace the whole magnetic glass board.
This product does not contain any parts that can be serviced by the consumer: it operates only with original parts.
Do not look directly at the light source when switched on.
Before each use, check the cable and plug for possible damage. Never use the board if it is damaged in any way.
Warning: a damaged plug can cause an electric shock or fire, resulting in injury or death.
The glass surface should be written on using only special markers for glass. The glass surface can be cleaned with a damp or dry cloth. Please do not use
abrasive scouring agents, detergents or chemicals to clean the board. The cleaning instructions for the board apply to the glass surface only. Do not clean the
board with fluid while the mains adapter is plugged in – danger of electric shock!
Do not allow any of the electrical components of the board to come into contact with water or other fluids.
Sigel GmbH does not assume any liability for incorrect mounting of the boards, a failure to follow the instructions for use, or for any resulting damage.
GUARANTEE
* We offer a 25-year guarantee that the glass surface will remain perfect to write on and to clean. We guarantee that the magnetic glass board will remain
easy to wipe free of smudges and other residue when using Sigel accessories and following our instructions for use. This guarantee does not apply in cases of
mistreatment, negligence, incorrect usage or other methods of utilisation that do not comply with the enclosed instructions.
MAGNETS
➔ Due to the thickness of the glass, only the enclosed SuperDym neodymium magnets or other extra-strong magnets can be used.
➔ If the distance between them is too small (< 10 cm), the magnets can collide, causing the magnetic coating to chip or the magnets to splinter.
➔ Danger of injury: fingers or skin can be squashed between two magnets, resulting in bruising.
➔ Magnets create a strong, far-reaching magnetic field. There is a risk of damage to cards with a magnetic strip, electronic appliances (data carriers, mobile phones,
computer, monitors, etc.), mechanical watches and hearing aids.
➔ People with pacemakers and heart defibrillator implants should avoid magnetic fields.
➔ Magnets are not a toy! Keep them out of the reach of children – small parts are a choking hazard.
TECHNICAL DATA
Light source:
60 LEDs/m, warm white 3000 K, 5 lumens/LED, 0.08 watts/LED
Wattage:
8,6 W (48 x 48 cm); 12,7 W (91 x 46 cm); 17,3 W (130 x 55 cm)
Mains voltage:
100-240 V, 50/60 Hz
Operating voltage: 12 V / DC; protection class 2
ENVIRONMENTAL PROTECTION
Electrical and electronic appliances must not be disposed of with household waste. As a consumer, you have a legal obligation to correctly dispose of the
appliances at the end of their service life at an official collection point for electronic waste.
EU DECLARATION OF CONFORMITY
Sigel GmbH hereby declares that this product, when used correctly, complies with the requirements and provisions of the low voltage directive, the elec-
tromagnetic compatibility directive and the restriction of hazardous substances directive. To request a copy of the declaration of conformity, contact us at
info@sigel.de.
5
Publicidad
Tabla de contenido
